|
|
Número de pieza | M215HW01-V0 | |
Descripción | LCD Module | |
Fabricantes | AUO | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de M215HW01-V0 (archivo pdf) en la parte inferior de esta página. Total 27 Páginas | ||
No Preview Available ! Product Specification
AU OPTRONICS CORPORATION
M215HW01 V0
( ) Preliminary Specification
( V ) Final Specification
Module
Model Name
21.5” Color TFT-LCD
M215HW01 V0
Customer
Date
Approved by
Note: This Specification is subject to
change without notice.
www.DataSheet4U.net
document version1.1
Approved by
Date
Sean Chen
2008/05/09
Prepared by
Boris Chu
2008/05/09
Desktop Display Business Group /
AU Optronics corporation
1
1 page Product Specification
AU OPTRONICS CORPORATION
M215HW01 V0
1.0 Handling Precautions
1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth
when handling.
7) Do not open or modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken
out from the container, do not press the center of the CCFL reflector edge. Instead, press at
the far ends of the CCFL Reflector edge softly. Otherwise the TFT Module may be damaged.
10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the
Interface Connector of the TFT Module.
11) After installation of the TFT Module into an enclosure, do not twist nor bend the TFT Module
even momentary. At designing the enclosure, it should be taken into consideration that no
bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT
Module may be damaged.
12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow
local ordinances or regulations for disposal.
13) Small amount of materials having no flammability grade is used in the LCD module. The LCD
module should be supplied by power complied with requirements of Limited Power Source
(IEC60950 or UL1950), or be applied exemption.
14) The LCD module is designed so that the CCFL in it is supplied by Limited Current Circuit
(IEC60950 or UL1950). Do not connect the CCFL in Hazardous Voltage Circuit.
document version1.1
5
5 Page Product Specification
AU OPTRONICS CORPORATION
M215HW01 V0
3.0 Functional Block Diagram
The following diagram shows the functional block of the 21.5 inch Color TFT-LCD Module:
LVDS
+5V
AUAOUOASIC
ASIC
LVDS
Receiver
Timing
Controller
RSDS
Transmitter
DC/DC
Converter
Gamma
Correction
G1
TFT-LCD
1920(x3) x 1080
Pixels
G1080
D1
X-Driver IC
D5760
4 CCFL
I/F + X-PCB
DC
Inverter
I/F PCB Interface:
FI-XB30SSRL-HF16 (JAE)
or AL230F-A0G1D-P(P-TWO)
Mating Type:
FI-X30HL (Locked Type)
document version 1.1
NUMPAGES |29}
11
11 Page |
Páginas | Total 27 Páginas | |
PDF Descargar | [ Datasheet M215HW01-V0.PDF ] |
Número de pieza | Descripción | Fabricantes |
M215HW01-V0 | LCD Module | AUO |
M215HW01-V2 | Color TFT-LCD | AUO |
M215HW01-V6 | LCD Module | AUO |
M215HW01-V7 | LCD MODULE | AUO |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |