DataSheet26.com

GS9025ACTME3 PDF даташит

Спецификация GS9025ACTME3 изготовлена ​​​​«GENNUM» и имеет функцию, называемую «Serial Digital Receiver».

Детали детали

Номер произв GS9025ACTME3
Описание Serial Digital Receiver
Производители GENNUM
логотип GENNUM логотип 

18 Pages
scroll

No Preview Available !

GS9025ACTME3 Даташит, Описание, Даташиты
GENLINX II GS9025A
Serial Digital Receiver
FEATURES
• SMPTE 259M compliant
• operational to 540Mb/s
• automatic cable equalization (typically greater than
350m of high quality cable at 270Mb/s)
• adjustment-free operation
• auto-rate selection (5 rates) with manual override
• single external VCO resistor for operation with five
input data rates
• data rate indication output
• serial data outputs muted and serial clock remains
active when input data is lost
• operation independent of SAV/EAV sync signals
• signal strength indicator output
• carrier detect with programmable threshold level
• power savings mode (output serial clock disable)
• Pb-free and Green
APPLICATIONS
Cable equalization plus clock and data recovery for all high
speed serial digital interface applications involving SMPTE
259M and other data standards.
DATA SHEET
DESCRIPTION
The GS9025A provides automatic cable equalization and
high performance clock and data recovery for serial digital
signals. The GS9025A receives either single-ended or
differential serial digital data and outputs differential clock
and retimed data signals at PECL levels (800mV). The on-
board cable equalizer provides up to 40dB of gain at
200MHz which typically results in equalization of greater
than 350m of high quality cable at 270Mb/s.
The GS9025A operates in either auto or manual data rate
selection mode. In both modes, the GS9025A requires only
one external resistor to set the VCO centre frequency and
provides adjustment free operation.
The GS9025A has dedicated pins to indicate signal
strength/carrier detect, LOCK and data rate. Optional
external resistors allow the carrier detect threshold level to
be customized to the user's requirement. In addition, the
GS9025A provides an 'Output Eye Monitor Test'
(OEM_TEST) for diagnostic testing of signal integrity after
equalization, prior to reslicing. The serial clock outputs can
also be disabled to reduce power. The GS9025A operates
from a single +5 or -5 volt supply.
ORDERING INFORMATION
PART NUMBER
GS9025ACQM
GS9025ACTM
GS9025ACQME3
GS9025ACTME3
PACKAGE
44 pin MQFP Tray
44 pin MQFP Tape
44 pin MQFP Tray
44 pin MQFP Tape
TEMPERATURE
0°C to 70°C
0°C to 70°C
0°C to 70°C
0°C to 70°C
Pb-FREE AND GREEN
No
No
Yes
Yes
A/D
DDI
ANALOG
CARRIER DETECT
DDI
DIGITAL
MUX
PHASELOCK
HARMONIC
SDI +
SDI --
VARIABLE
GAIN EQ
STAGE
OEM_TEST
EYE
MONITOR
AUTO EQ
CONTROL
FREQUENCY
ACQUISITION
PHASE
DETECTOR
DIVISION
+-
AGC CAP CD_ADJ
CHARGE
PUMP
VCO
SSI/CD LF+ LFS LF-
CBG RVCO
BLOCK DIAGRAM
COSC
LOGIC MUTE
3 BIT
COUNTER
DECODER
LOCK
SDO
SDO
CLK_EN
SCO
SCO
SMPTE
AUTO/MAN
SS0
SS1
SS2
Revision Date: August 2005
GENNUM CORPORATION P.O. Box 489, Stn. A, Burlington, Ontario, Canada L7R 3Y3
Tel. +1 (905) 632-2996 Fax. +1 (905) 632-5946 E-mail: [email protected]
www.gennum.com
Document No. 522 - 75 - 05









No Preview Available !

GS9025ACTME3 Даташит, Описание, Даташиты
ABSOLUTE MAXIMUM RATINGS
PARAMETER
Supply Voltage (VS)
Input Voltage Range (any input)
Operating Temperature Range
Storage Temperature Range
Lead Temperature (soldering, 10 sec)
VALUE
5.5V
VCC + 0.5 to VEE - 0.5V
0°C TA 70°C
-65°C TS 150°C
260°C
DC ELECTRICAL CHARACTERISTICS
VCC = 5.0V, TA = 0° to 70°C unless otherwise stated, RLF = 1.8k, CLF1 = 15nF, CLF2 = 3.3pF
PARAMETER
CONDITION
MIN
TYPICAL1
MAX
UNITS NOTES
Supply Voltage
Supply Current
SDI Common Mode Voltage
DDI Common Mode Input
Voltage Range
DDI Differential Input Drive
SSI/CD Output Current
OEM_TEST Bias Potential
A/D
AUTO/MAN, SMPTE, SS[2:0]
Input Voltage
CLK_EN Input Voltage
LOCK Output Low Voltage
SS[2:0] Output Voltage
CLK_EN = 0
CLK_EN = 1
HIGH, 100m,
143Mb/s, ΙOH=-10µA
HIGH, 300m,
143Mb/s, ΙOH=-10µA
LOW, ΙOL=1mA
RL=50Ω
High
Low
High
Low
High
Low
ΙOL=500µA
HIGH, ΙOH=-180µA,
Auto Mode
LOW, ΙOL=600µA,
Auto Mode
4.75
-
-
-
VEE+(VDIFF/2)
200
-
-
-
-
2.3
-
2.0
-
2.5
-
-
4.4
-
5
115
125
2.4
0.4 to 4.6
5.25
-
VCC-(VDIFF/2)
800 2000
4.2 -
3.7 -
0.4 0.8
4.75 -
--
- 0.8
--
- 0.8
--
- 0.8
0.25 0.4
4.8 -
0.3 0.4
V
mA
mA
V
V
mV
V
V
V
V
V
V
V
V
2
5
3
TEST
LEVEL
3
9
3
3
3
3
3
1
3
3
3
3
1
1
GENNUM CORPORATION
2 of 18
522 - 75 - 05









No Preview Available !

GS9025ACTME3 Даташит, Описание, Даташиты
DC ELECTRICAL CHARACTERISTICS (Continued)
VCC = 5.0V, TA = 0° to 70°C unless otherwise stated, RLF = 1.8k, CLF1 = 15nF, CLF2 = 3.3pF
PARAMETER
CONDITION
MIN
TYPICAL1
MAX
UNITS NOTES
TEST
LEVEL
SS[2:0] Input Voltage
HIGH, Manual Mode
2
- -V
3
LOW, Manual Mode
-
- 0.8
CLK_EN Source Current
Low, VIL = 0V
- 26 55 µA
1
NOTES
1. TYPICAL - measured on EB9025A board.
2. VDIFF is the differential input signal swing.
3. LOCK is an open collector output and requires an external pull-up
resistor.
4. Pins SS[2:0] are outputs in AUTO mode and inputs in MANUAL mode.
5. If OEM_TEST is permanently enabled, operating temperature range is
limited from 0°C to 60°C inclusive.
TEST LEVELS
1. Production test at room temperature and nominal supply
voltage with guardbands for supply and temperature
ranges.
2. Production test at room temperature and nominal supply
voltage with guardbands for supply and temperature
ranges using correlated test.
3. Production test at room temperature and nominal supply
voltage.
4. QA sample test.
5. Calculated result based on Level 1,2, or 3.
6. Not tested. Guaranteed by design simulations.
7. Not tested. Based on characterization of nominal parts.
8. Not tested. Based on existing design/characterization
data of similar product.
9. Indirect test.
AC ELECTRICAL CHARACTERISTICS
VCC = 5.0V, VEE = 0V, TA = 0° to 70°C unless otherwise stated, RLF = 1.8k, CLF1 = 15nF, CLF2 = 3.3pF
PARAMETER
CONDITIONS
MIN TYPICAL1
MAX
Serial Data Rate
SDI
Maximum Equalizer Gain
@ 200MHz
Additive Jitter
[Pseudorandom (223 -1)]
270Mb/s, 300m
(Belden 8281)
540Mb/s, 100m
(Belden 8281)
Intrinsic Jitter
[Pseudorandom (223 -1)]
270Mb/s
540Mb/s
Intrinsic Jitter
[Pathological (SDI checkfield)]
270Mb/s
360Mb/s
540Mb/s
Input Jitter Tolerance
270Mb/s
540Mb/s
Lock Time -
Synchronous Switch
tswitch < 0.5µs, 270Mb/s
0.5µs< tswitch <10ms
tswitch > 10 ms
Lock Time -
Asynchronous Switch
Loop Bandwidth
= 6MHz @ 540Mb/s
143
-
-
-
-
-
-
-
-
0.40
0.32
-
-
-
-
- 540
40 -
300 -
275 -
185 see Figure 12
164
462 see Figure 13
308
260
0.56 -
0.43 -
1-
1-
4-
10 -
UNITS
Mb/s
dB
ps p-p
ps p-p
ps p-p
UI p-p
µs
ms
ms
ms
NOTES
TEST
LEVEL
3
6
2, 8 9
2, 7 4
2, 7 3
3, 7 9
47
57
GENNUM CORPORATION
3 of 18
522 - 75 - 05










Скачать PDF:

[ GS9025ACTME3.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
GS9025ACTME3Serial Digital ReceiverGENNUM
GENNUM

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск