DataSheet26.com

AH373 PDF даташит

Спецификация AH373 изготовлена ​​​​«Diodes Incorporated» и имеет функцию, называемую «INTERNAL PULL-UP HALL EFFECT LATCH».

Детали детали

Номер произв AH373
Описание INTERNAL PULL-UP HALL EFFECT LATCH
Производители Diodes Incorporated
логотип Diodes Incorporated логотип 

12 Pages
scroll

No Preview Available !

AH373 Даташит, Описание, Даташиты
AH373
INTERNAL PULL-UP HALL EFFECT LATCH
Description
AH373 is a single-digital-output Hall-Effect latch sensor with internal
pull-up resistor for high temperature operation. The device includes
an on-chip Hall voltage generator for magnetic sensing, an amplifier
to amplify Hall voltage, and a comparator to provide switching
hysteresis for noise rejection, and an output driver with a pull-up
resistor. An internal band-gap regulator provides a temperature
compensated supply voltage for internal circuits and allows a wide
operating supply range.
When the magnetic flux density (B) perpendicular to the package is
larger than operate point (Bop), output is switched on (OUT pin is
pulled low). The output state is held on until a magnetic flux density
reversal falls below Brp. When B is less than Brp, the output is
switched off.
The AH373 is available in SIP-3L, SC59 and SOT23 packages.
Pin Assignments
(TOP View)
SC59 and SOT23
(TOP View)
SIP-3L
3. OUT
2. GND
1. VDD
Features
Bipolar Hall Effect Latch Operation
2.2V to 20V Operating Range
Single Output with Built-in Pull-up Resistor
25mA output Sink Capability
-40C to +125°C Operating Temperature
Industry Standard SIP-3L, SC59 and SOT23 Packages
Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2)
Halogen and Antimony Free. “Green” Device (Note 3)
Applications
Rotor Position Sensing for Motor Commutation
Encoder
Speed Measurement – RPM Monitor
Contact-less Current Switch
Notes:
1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant.
2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green"
and Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and
<1000ppm antimony compounds.
Typical Application Circuits
IA
IB
Driver
&
IC
Ia
Ib
Ic
Control Logic
HA
HB
HC
Hall Motor Driver
M
RPM sensing
Digital Hall Effect Sensor
M: Three Phase Hall Motor
3 Phase Hall Motor
AH373
Document number: Draft DS31173 Rev. 11 - 2
1 of 12
www.diodes.com
September 2013
© Diodes Incorporated









No Preview Available !

AH373 Даташит, Описание, Даташиты
Typical Application Circuits (cont.)
AH373
Note:
Typical AH373 Circuit
4. CIN is for power stabilization and to strengthen the noise immunity, the recommended capacitance is 100nF typical
Pin Descriptions
Package: SC59, SOT23 and SIP-3L
Pin Number
1
2
3
Pin Name
VDD
GND
OUTPUT
Function
Power Supply Input
Ground
Output
Functional Block Diagram
VDD
1
Regulator
Hall
plate
Amp
Rpu
23 OUTPUT
2 GND
AH373
Document number: Draft DS31173 Rev. 11 - 2
2 of 12
www.diodes.com
September 2013
© Diodes Incorporated









No Preview Available !

AH373 Даташит, Описание, Даташиты
AH373
Absolute Maximum Ratings (Note 5) @TA = +25°C, unless otherwise specified.)
Symbol
VDD
VOUT (Off)
IO (sink)
B
PD
TS
TJ
Supply Voltage (Note 6)
Output “Off” Voltage
Output “On” current (sink)
Magnetic Flux Density
Characteristics
Package Power Dissipation
Storage Temperature Range
Maximum Junction Temperature
SIP-3L
SC59 and SOT23
Values
28
28
25
Unlimited
550
230
-65 to +150
+150
Unit
V
V
mA
mW
mW
°C
°C
Notes:
5. Stresses greater than the 'Absolute Maximum Ratings' specified above may cause permanent damage to the device. These are stress ratings only;
functional operation of the device at these or any other conditions exceeding those indicated in this specification is not implied. Device reliability may be
affected by exposure to absolute maximum rating conditions for extended periods of time.
6. The absolute maximum VDD of 28V is a transient stress rating and is not meant as a functional operating condition. It is not recommended to operate
the device at the absolute maximum rated conditions for any period of time.
Recommended Operating Conditions (@TA = +25°C, unless otherwise specified.)
Symbol
VDD
TA
Characteristic
Supply Voltage (Note 7)
Operating Temperature Range
Conditions
Operating
Operating
Rating
2.2 to 20
-40 to +125
Unit
V
°C
Note:
7. The output of IC will be switched after the supply voltage is over 2.2V, but the magnetic characteristics will not be normal until the supply is over 2.5V.
Electrical Characteristics (@TA = +25°C, VDD = 12V, unless otherwise specified.)
Symbol
VOUT
IDD
IOFF
Rpu
Characteristic
Output On Voltage
Supply Current
Output Leakage Current
Internal Pull-up Resistor
Conditions
IOUT = 20mA
B < Brp
Output off
Min
7
Typ
300
2
< 0.1
10
Max
400
4
10
13
Unit
mV
mA
µA
k
AH373
Document number: Draft DS31173 Rev. 11 - 2
3 of 12
www.diodes.com
September 2013
© Diodes Incorporated










Скачать PDF:

[ AH373.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
AH372INTERNAL PULL-UP HALL EFFECT LATCHDiodes
Diodes
AH373Internal Pull-up Hall Effect LatchAnachip
Anachip
AH373INTERNAL PULL-UP HALL EFFECT LATCHDiodes Incorporated
Diodes Incorporated
AH375Single Phase Hall Effect LatchAnachip
Anachip

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск