|
|
PDF LTM12C324C Data sheet ( Hoja de datos )
| Número de pieza | LTM12C324C | |
| Descripción | TFT LCD Module | |
| Fabricantes | Toshiba | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LTM12C324C (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
Global LCD Panel Exchange Center
www.panelook.com
To: Compal Electronics, Inc.
APPROVAL SIGNATURE
SPECIFICATION
FOR
TOSHIBA MATSUSHITA DISPLAY TECHNOLOGY
TFT-LCD MODULE
LT M 1 2 C 3 2 4 C
SPECIFICATION No. :
N L - LT M 1 2 C 3 2 4 C - 2 1
DATE OF ISSUE : 2003-02-28
(DATE OF EXPIRY : 2006-02-27)
H. Yamaguchi
General Manager
Quality Assurance Div.
<Engineering Department to contact as per SPECIFICATION>
PC.Monitor-Use Marketing & Engineering Dept.
PC.Monitor-Use LCD Div.
Toshiba Matsushita Display Technology Co.,Ltd.
1-9-2, Hatara-cho, Fukaya-shi, Saitama, 366-0032, JAPAN
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
1 page  
Global LCD Panel Exchange Center
www.panelook.com
Specification No.
Sheet 4
For Installation in Assembly
(1) The C-MOS LSIs used in LCD module are very sensitive to ESD (Electro-static Discharge).
Ambient humidity of working area is recommended to be higher than 50%(RH).
Person handling LCD modules should be grounded with wrist band. Tools like soldering iron and screwdriver, and
working benches should be grounded.
The grounding should be done through a resistor of 0.5-1Mohms in order to prevent spark of ESD.
(2) When remove protection film from LCD panel, peer off the film slowly (more than three seconds) from the edge of
the panel, using a soft-pointed tweezers covered by Teflon or adherent tape.
(3) Reduce dust level in working area. Especially the level of metal particle should be decreased.
Use fingerstalls or soft and dust-free gloves in order to keep clean appearance of LCD module when handled for
incoming inspection and assembly.
*(4) When LCD panel becomes dirty, wipe off the panel surface softly with absorbent cotton or another soft cloth.
If necessary, breathe upon the panel surface and then wipe off immediately and softly again.
If the dirt can not be wiped off, absorbent cotton wetted a little with normal-hexane or petroleum benzine can be
used for wiping the panel.
Be careful not to spill this solvent into the inside of LCD module. Driver ICs and PCB area used inside LCD module
may be damaged by the solvent.
*(5) AVOID THE CONDENSATION OF WATER
Wipe off a spot or spots of water of mist and chemicals of mist on LCD panel softly with absorbent cotton or another
cloth as soon as possible if happened, otherwise discoloration or stain may be caused. If water invade into LCD
module, it may cause LCD module damages.
*(6) Do not expose LCD module to the gas (which is not normally contained in the atmosphere), it may cause
mis-operation or defects.
*(7) DO NOT APPLY MECHANICAL FORCES.
Do not bend or twist LCD module even momentary when LCD module is installed an enclosure of the system.
Bending or twisting LCD module may cause its damages.
Make sure to design the enclosure that bending/twisting forces are not applied to LCD module when it is installed in
the system.
Refrain from strong mechanical shock like dropping from the working bench or knocking against hard object.
These may cause glass of the panel crack, damage of FL or other mis-operation.
*(8) Refrain from excessive force like pushing the surface of LCD panel. This may cause damage of the panel or
electrical parts on PCB.
*(9) Do not put heavy object such as tools, books, etc., and do not pile up LCD modules.
Be careful not to touch surface of the polarizer laminated to the panel with any hard and sharp object. The polarizer
is so soft that it can easily scratched, even the protect film covers it.
(10) When inserting or disconnecting the connectors to LCD module, be sure not to apply force against PCB, nor
connecting cables, otherwise internal connection of PCB and TAB drivers may be damaged.
Do not fasten screws while putting cables like those for interface or FL between LCD module and the enclosure.
Make sure to insert the module FL connector to the inverter connector in correct position.
If incorrect, this may cause smoke or burn of electrical parts by high voltage of FL circuit.
Toshiba Matsushita Display Technology Co.,Ltd
Date: 2003-02-28 New No. NL-LTM12C324C-21
Date:
- - Old No.
m# Special m Addition m Change
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
5 Page 
Global LCD Panel Exchange Center
www.panelook.com
Specification No.
(Rear figure)
Sheet 10
Toshiba Matsushita Display Technology Co.,Ltd
Date: 2003-02-28 New No. NL-LTM12C324C-21
Date:
- - Old No.
m# Special m Addition m Change
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet LTM12C324C.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LTM12C324C | TFT LCD Module | Toshiba |
| LTM12C324S | TFT LCD Module | Toshiba |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |