|
|
PDF LTM12C505N Data sheet ( Hoja de datos )
| Número de pieza | LTM12C505N | |
| Descripción | TFT LCD Module | |
| Fabricantes | Toshiba | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LTM12C505N (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
Global LCD Panel Exchange Center
www.panelook.com
To: W istron Corporation
This specification is only used for discussing the included items.
You haven’t to approve this specification.
When we shall agree the specification, we will issue the formal one.
SPECIFICATION(TENTATIVE)
FOR
TOSHIBA TFT-LCD MODULE
LT M 1 2 C 5 0 5 N
NR-LTM12C505N-01
DATE OF ISSUE: 2001-10-26
Liquid Crystal Display Device Marketing & Engineering Dept.
Liquid Crystal Display Div.
TOSHIBA Corporation, Display Devices & Components Company
8, Shinsugita-cho, Isogo-ku, Yok ohama, 235-8522, JAPAN
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
1 page  
Global LCD Panel Exchange Center
www.panelook.com
Specification No.
Sheet 4
For Installation in Assembly
(1) The C-MOS LSIs used in LCD module are very sensitive to ESD (Electro-static Discharge).
Ambient humidity of working area is recommended to be higher than 50%(RH).
Person handling LCD modules should be grounded with wrist band. Tools like soldering iron and screw driver, and
working benches should be grounded.
The grounding should be done through a resistor of 0.5-1MΩ in order to prevent spark of ESD.
(2) When remove protection film from LCD panel, peer off the film slowly (more than three seconds) from the edge of the
panel, using a soft-pointed tweezers covered by Teflon or adherent tape.
(3) Reduce dust level in working area. Especially the level of metal particle should be decreased.
Use finger stalls or soft and dust-free gloves in order to keep clean appearance of LCD module when handled for
incoming inspection and assembly.
✳(4) When LCD panel becomes dirty, wipe off the panel surface softly with absorbent cotton or another soft cloth.
If necessary, breathe upon the panel surface and then wipe off immediately and softly again.
If the dirt can not be wiped off, absorbent cotton wetted a little with normal-hexane or petroleum benzine can be used for
wiping the panel.
Be careful not to spill this solvent into the inside of LCD module. Driver ICs and PCB area used inside LCD module may
be damaged by the solvent.
✳(5) AVOID THE CONDENSATION OF WATER
Wipe off a spot or spots of water of mist and chemicals of mist on LCD panel softly with absorbent cotton or another cloth
as soon as possible if happened, otherwise discoloration or stain may be caused. If water invade into LCD module, it may
cause LCD module damages.
✳(6) Do not expose LCD module to the gas (which is not normally contained in the atmosphere), it may cause mis-operation or
defects.
✳(7) DO NOT APPLY MECHANICAL FORCES.
Do not bend or twist LCD module even momentary when LCD module is installed an enclosure of the system. Bending or
twisting LCD module may cause its damages.
Make sure to design the enclosure that bending/twisting forces are not applied to LCD module when it is installed in the
system.
Refrain from strong mechanical shock like dropping from the working bench or knocking against hard object.
These may cause glass of the panel crack, damage of FL or other mis-operation.
✳(8) Refrain from excessive force like pushing the surface of LCD panel. This may cause damage of the panel or electrical
parts on PCB.
✳(9) Do not put heavy object such as tools, books, etc., and do not pile up LCD modules.
Be careful not to touch surface of the polarizer laminated to the panel with any hard and sharp object. The polarizer is so
soft that it can easily scratched, even the protect film covers it.
(10) When inserting or disconnecting the connectors to LCD module, be sure not to apply force against PCB, nor connecting
cables, otherwise internal connection of PCB and TAB drivers may be damaged.
Do not fasten screws while putting cables like those for interface or FL between LCD module and the enclosure.
Make sure to insert the module FL connector to the inverter connector in correct position.
If incorrect, this may cause smoke or burn of electrical parts by high voltage of FL circuit.
LIQUID CRYSTAL DISPLAY DIVISION
Date:2001-10-26
Date: - -
New No.NR-LTM12C505N-01
Old No.
←# Special ←& Addition ← Change
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
5 Page 
Global LCD Panel Exchange Center
www.panelook.com
Specification No.
Warning
Sheet 10
HIGH VOLTAGE
‚b‚` ‚t ‚s ‚h ‚n ‚m
RISK OF ELECTRIC.
DISCONNECT THE ELECTRIC POWER
BEFORE SERVICING
Never push this area
COLD CATHODE FLUORESCENT LAMP IN LCD PANEL CON- 1 0 / . - , + * ) ( ' & %
TAINS A SMALL AMOUNT OF MERCURY,PLEASE FOLLOW $ # " !
LOCAL ORDINANCES OR REGULATIONS FOR DISPOSAL.
Note 1) Never push this area. Pushing here may cause the LCD being damaged.
LIQUID CRYSTAL DISPLAY DIVISION
Date:2001-10-26
Date: - -
New No.NR-LTM12C505N-01
Old No.
←# Special ←& Addition ← Change
One step solution for LCD / PDP / OLED panel application: Datasheet, inventory and accessory! www.panelook.com
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet LTM12C505N.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LTM12C505D | TFT LCD Module | Toshiba |
| LTM12C505N | TFT LCD Module | Toshiba |
| LTM12C505W | TFT LCD Module | Toshiba |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |