DataSheet26.com

AH1804 PDF даташит

Спецификация AH1804 изготовлена ​​​​«Diodes» и имеет функцию, называемую «MICROPOWER OMNIPOLAR HALL EFFECT SENSORSWITCH».

Детали детали

Номер произв AH1804
Описание MICROPOWER OMNIPOLAR HALL EFFECT SENSORSWITCH
Производители Diodes
логотип Diodes логотип 

9 Pages
scroll

No Preview Available !

AH1804 Даташит, Описание, Даташиты
AH1804
MICROPOWER OMNIPOLAR HALL EFFECT SENSORSWITCH
Description
The AH1804 is a micropower Omnipolar Hall effect switch IC
with a single output driver with internal pull up and pull down
capability. Designed for portable and battery powered
equipment such as cellular phones and portable PCs the
average supply current is only 12µA at 3.3V. To support
battery powered equipment the AH1804 can operate over the
supply range of 2.5V to 3.6V and uses a hibernating clocking
system to minimize the power consumption.
Pin Assignments
( Top View )
GND
4
NC
3
12
VDD Output
DFN1216-4
The output is activated with either a north or south pole of
sufficient strength. When the magnetic flux density (B) is
larger than operate point (Bop), the output will be turned on
(pulled low) and held until B is lower than release point (Brp).
The AH1804 is available in SC59 and small low profile
DFN1216-4 packages.
(Top View)
GND 2.
SC59
3. Output
1 . VDD
Features
Omnipolar operation (North or South pole)
Low supply voltage 2.5V to 3.6V
Micropower operation
No external pull up resistors required
Chopper stabilized design
o Superior temperature stability
o Extremely Low Switch-Point Drift
o Insensitive to Physical Stress
Good RF noise immunity
-40°C to 85°C operating temperature
Small low profile DFN1216-4 and SC59 packages
ESD (HBM) 5KV
“Green” Molding Compound
Applications
Cover switch in clam-shell and slide cellular phones
Cover switch in portable PC’s, Tablets and PDA
Display screen open/close detect in Digital
camcorders
Contact-less switch in portable battery powered
consumer and industrial products
Typical Application Circuit
VDD
2.5V to 3.6V
Cin
AH1804
Output
GND
Note: Cin is for power stabilization and to strengthen the noise immunity, C = 100nF or higher must be used.
AH1804
Document number: DS35314 Rev. 2 - 2
1 of 9
www.diodes.com
September 2011
© Diodes Incorporated
Free Datasheet http://www.Datasheet4U.com









No Preview Available !

AH1804 Даташит, Описание, Даташиты
AH1804
MICROPOWER OMNIPOLAR HALL EFFECT SENSORSWITCH
Pin Descriptions
Pin Name
P/I/O
Description
VDD
GND
P/I Power Supply Input
P/I Ground
Output
O Output Pin
NC NC No Connection (Note 1)
Notes: 1. NC is “No Connection” which is not connected internally. This pin can be left open or tied to ground.
Functional Block Diagram
VDD
Hall
Plate
Hall
Plate
Amp
Amp
Sleep/Awake Logic
and Power Switch
Latch
Latch
Output
Driver
Controller
Output
GND
AH1804
Document number: DS35314 Rev. 2 - 2
2 of 9
www.diodes.com
September 2011
© Diodes Incorporated
Free Datasheet http://www.Datasheet4U.com









No Preview Available !

AH1804 Даташит, Описание, Даташиты
AH1804
MICROPOWER OMNIPOLAR HALL EFFECT SENSORSWITCH
Absolute Maximum Ratings (TA = 25°C, Note 2)
Symbol
Characteristics
Values
Unit
VDD Supply voltage (Note 3)
5.0 V
VDD rev
B
Reverse supply voltage
Magnetic flux density
-0.3
Unlimited
V
Ts Storage Temperature Range
-65 to +150
°C
PD Package Power Dissipation
DFN1216-4
SC59
230
mW
270
TJ Maximum Junction Temperature
150 °C
Notes:
2. Stresses greater than the 'Absolute Maximum Ratings' specified above, may cause permanent damage to the device. These are stress ratings
only; functional operation of the device at these or any other conditions exceeding those indicated in this specification is not implied.
Device reliability may be affected by exposure to absolute maximum rating conditions for extended periods of time
3. The absolute maximum of 5V is a transient stress rating and is not meant as functional operating conditions. It is not recommended to operate the
device at the absolute maximum rated conditions for any period of time.
Recommended Operating Conditions (TA = 25°C)
Symbol
Characteristics
Conditions
VDD Supply Voltage
TA Operating Temperature Range
CIN =0.1µF (Note 4)
Operating
Notes: 4. Decoupling capacitor CIN = 100nF or higher must be used for full 2.5V to 3.6V supply range.
Rating
2.5 to 3.6
-40 to +85
Unit
V
°C
Electrical Characteristics (TA = 25°C, VDD = 3.3V, unless otherwise specified)
Symbol
VOL
VOH
Idd(en)
Idd(dis)
Idd(avg)
Tawake
Tperiod
D.C.
Characteristics
Output Low Voltage (on)
Output High Voltage (off)
Supply current
Awake Time
Period
Duty Cycle
Conditions
IOUT = 1mA
IOUT = -1mA
Chip enable
Chip disable
Average supply current,
(Note 5)
(Note 5)
Min
VDD-0.2
Typ.
0.1
VDD-0.1
4
8
12
50
50
0.1
Notes: 5. When power is initially on, the operating VDD (2.5V to 3.6V) must be applied to be guaranteed for the output sampling.
The output state is valid after the second operating phase (typical 100ms).
Max
0.2
⎯⎯
100
100
Unit
V
V
mA
µA
µA
µs
ms
%
AH1804
Document number: DS35314 Rev. 2 - 2
3 of 9
www.diodes.com
September 2011
© Diodes Incorporated
Free Datasheet http://www.Datasheet4U.com










Скачать PDF:

[ AH1804.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
AH180MICROPOWER OMNIPOLAR HALL-EFFECT SENSOR SWITCHDiodes Incorporated
Diodes Incorporated
AH1801ULTRA-SENSITIVE HALL EFFECT SWITCHDiodes
Diodes
AH1802ULTRA-SENSITIVE OMNIPOLAR HALL-EFFECT SENSOR SWITCHDiodes
Diodes
AH1803ULTRA-SENSITIVE HALL EFFECT SWITCHDiodes
Diodes

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск