DataSheet26.com

LCP102E PDF даташит

Спецификация LCP102E изготовлена ​​​​«micropowerdirect» и имеет функцию, называемую «1W Miniature SMT DC/DC Con vert ers».

Детали детали

Номер произв LCP102E
Описание 1W Miniature SMT DC/DC Con vert ers
Производители micropowerdirect
логотип micropowerdirect логотип 

2 Pages
scroll

No Preview Available !

LCP102E Даташит, Описание, Даташиты
LCP100E Series
Low Cost, 1W
Miniature SMT
DC/DC Converters
Key Features:
Electrical Specifications
Specifications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specifications subject to change without notice.
Input
1W Output Power
Parameter
Conditions
Min. Typ. Max. Units
Miniature SMT Case
Input Voltage Range
DCP01 Series Replacement
5 VDC Input 4.50 5.0 5.50
12 VDC Input 10.80 12.0 13.20
VDC
1,500 VDC Isolation
Input Filter
Internal Capacitor
Short Circuit Protected
Output
>3.5 MHour MTBF
DIP Ver Available (ACP100E)
LOW, LOW COST!!
Parameter
Output Voltage Accuracy
Line Regulation
Load Regulation, See Note 1
Conditions
Min. Typ.
±3.0
For Vin Change of 1%
See Model Selection Guide
Max.
±1.2
Units
%
%
Ripple & Noise (20 MHz), See Note 3
50% Iout
100% Iout
20
mV P - P
50 75
Temperature Coefficient
±0.03 %/°C
Output Short Circuit, See Note 4
Continuous (Autorecovery)
General
Parameter
Conditions
Min. Typ. Max. Units
Isolation Voltage
60 Seconds 1,500
VDC
Isolation Resistance
500 VDC 1,000
M
Isolation Capacitance
100 kHz, 1V
25
pF
Switching Frequency
100 kHz
Environmental
Parameter
Conditions
Min. Typ. Max. Units
Operating Temperature Range
Ambient -40 +25 +85
°C
Operating Temperature Range
Case
+100
°C
Storage Temperature Range
-55
+125
°C
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95 %
Physical
Case Size
0.77 x 0.42 x 0.18 Inches (19.5 x 10.53 x 4.5 mm)
Case Material
Non-Conductive Black Plastic (UL-94V0)
MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
W: www.micropowerdirect.com
Weight
Reliability Specifications
Parameter
MTBF
Shock & Vibration, See Note 5
Absolute Maximum Ratings
Parameter
Input Voltage Surge (1 Sec)
0.05 Oz (1.4g)
Conditions
MIL HDBK 217F, 25°C, Gnd Benign
Min. Typ. Max. Units
3.5 MHours
Meets MIL-STD-202F, IEC68-2-6
Conditions
Min. Typ. Max.
5 VDC Input -0.7
9.0
12 VDC Input -0.7
18.0
Units
VDC
Lead Temperature
1.5 mm From Case For 10 Sec
260 °C
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
www.micropowerdirect.com
http://www.Datasheet4U.com









No Preview Available !

LCP102E Даташит, Описание, Даташиты
Model Selection Guide
www.micropowerdirect.com
Model
Number
LCP101E
LCP102E
LCP103E
LCP104E
LCP111E
LCP112E
LCP113E
LCP114E
Input
Voltage (VDC)
Current (mA)
Nominal Range Full-Load No-Load
5
4.5 - 5.5
270
50
5
4.5 - 5.5
256
50
5
4.5 - 5.5
260
50
5
4.5 - 5.5
263
50
12 10.8 - 13.2 114
20
12 10.8 - 13.2 127
20
12 10.8 - 13.2 110
20
12 10.8 - 13.2 111
20
Voltage
(VDC)
5.0
9.0
12.0
15.0
5.0
9.0
12.0
15.0
Output
Current
(mA, Max)
200.0
111.0
83.0
67.0
200.0
111.0
83.0
67.0
Current
(mA, Min)
20.0
12.0
9.0
7.0
20.0
12.0
9.0
7.0
Load Regulation
(% Typ)
12.8
8.3
6.8
6.3
12.8
8.3
6.8
6.3
(% Max)
15.0
15.0
15.0
15.0
15.0
15.0
15.0
15.0
Efficiency
(%, Typ)
74
78
77
76
73
74
76
75
Fuse Rating
Slow-Blow
(mA)
500
500
500
500
200
200
200
200
Notes:
1. Output load regulation is specified for a load change of 10% to 100%.
Derating Curve
2. These units should not be operated with a load under 10% of full load. Operation
at no-load may cause damage to the unit.
3. These converters will operate without external components. However, when measur-
ing output ripple, it is recommended that an external ceramic capacitor be placed
from the +Vout pin to the
-Vout pin. An input capacitor
will enhance stability over
Vin
Input
Capacitor
Vout
Output
Capacitor
temperature and input line
variations. Recommended
5 VDC
capacitor values are given 12 VDC
4.7 µF 5 VDC 10.0 µF
2.2 µF 9 VDC 4.7 µF
in the table at right. For
12 VDC 2.2 µF
applications requiring very
low output noise levels, a
15 VDC 1.0 µF
simple LC filter should be effective.
4. Given for frequency range of 5 to 500 Hz and PSD of 0.0248 g2/Hz.
Tested on X, Y & Z axis for 60 minutes.
5. It is recommended that a fuse be used on the input of a power supply for protection.
See the Model Selection table above for the correct rating.
Mechanical Dimensions
Pin
Connections
Pin Function
1 +Vin
2 -Vin
5 -Vout
6 +Vout
7 NC
8 NC
14 NC
NC = No Connection
MicroPower Direct
Notes:
All dimensions are typical in inches (mm)
Tolerance x.xx = ±0.01 (±0.25)
Pin 1 is marked by a “dot” or indentation on the top of the unit
We Power Your Success - For Less!
292 Page Street Ste D Stoughton, MA 02072 TEL: (781) 344-8226 FAX: (781) 344-8481 E-Mail: [email protected]
http://www.Datasheet4U.com










Скачать PDF:

[ LCP102E.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
LCP102E1W Miniature SMT DC/DC Con vert ersmicropowerdirect
micropowerdirect

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск