|
|
PDF LM3410 Data sheet ( Hoja de datos )
| Número de pieza | LM3410 | |
| Descripción | Constant Current Boost and SEPIC LED Driver | |
| Fabricantes | National Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de LM3410 (archivo pdf) en la parte inferior de esta página. Total 32 Páginas | ||
|
No Preview Available !
January 23, 2008
LM3410
PowerWise® 525kHz/1.6MHz, Constant Current Boost and
SEPIC LED Driver with Internal Compensation
General Description
The LM3410 constant current LED driver is a monolithic, high
frequency, PWM DC/DC converter in 5-pin SOT23, 6-pin LLP,
& 8-pin eMSOP packages. With a minimum of external com-
ponents the LM3410 is easy to use. It can drive 2.8A typical
peak currents with an internal 170 mΩ NMOS switch. Switch-
ing frequency is internally set to either 525 kHz or 1.60 MHz,
allowing the use of extremely small surface mount inductors
and chip capacitors. Even though the operating frequency is
high, efficiencies up to 88% are easy to achieve. External
shutdown is included, featuring an ultra-low standby current
of 80 nA. The LM3410 utilizes current-mode control and in-
ternal compensation to provide high-performance over a wide
range of operating conditions. Additional features include
dimming, cycle-by-cycle current limit, and thermal shutdown.
Features
■ Space Saving SOT23-5 & 6-LLP Package
■ Input voltage range of 2.7V to 5.5V
■ Output voltage range of 3V to 24V
■ 2.8A Typical Switch Current
■ High Switching Frequency
— 525 KHz (LM3410-Y)
— 1.6 MHz (LM3410-X)
■ 170 mΩ NMOS Switch
■ 190 mV Internal Voltage Reference
■ Internal Soft-Start
■ Current-Mode, PWM Operation
■ Thermal Shutdown
Applications
■ LED Backlight Current Source
■ LiIon Backlight OLED & HB LED Driver
■ Handheld Devices
■ LED Flash Driver
Typical Boost Application Circuit
30038501
© 2008 National Semiconductor Corporation 300385
30038502
www.national.com
Free Datasheet http://www.datasheet4u.com/
1 page  
Symbol
θJA
θJC
TSD
Parameter
Conditions
Junction to Ambient
0 LFPM Air Flow (Note 3)
LLP-6 and eMSOP-8 Package
SOT23-5 Package
Junction to Case (Note 3)
LLP-6 and eMSOP-8 Package
SOT23-5 Package
Thermal Shutdown Temperature (Note 2)
Min Typ Max Units
- 80 -
°C/W
- 118 -
- 18 -
°C/W
- 60 -
- 165 -
°C
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but does not guarantee specific performance limits. For guaranteed specifications and conditions, see the Electrical Characteristics.
Note 2: Thermal shutdown will occur if the junction temperature exceeds the maximum junction temperature of the device.
Note 3: Applies for packages soldered directly onto a 3” x 3” PC board with 2oz. copper on 4 layers in still air.
Note 4: The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin. Test method is per JESD22-A114.
Note 5: Do not allow this pin to float or be greater than VIN +0.3V.
5 www.national.com
Free Datasheet http://www.datasheet4u.com/
5 Page 
of the capacitor’s reactance and its equivalent series resis-
tance (ESR):
When using MLCCs, the ESR is typically so low that the ca-
pacitive ripple may dominate. When this occurs, the output
ripple will be approximately sinusoidal and 90° phase shifted
from the switching action.
Given the availability and quality of MLCCs and the expected
output voltage of designs using the LM3410, there is really no
need to review any other capacitor technologies. Another
benefit of ceramic capacitors is their ability to bypass high
frequency noise. A certain amount of switching edge noise
will couple through parasitic capacitances in the inductor to
the output. A ceramic capacitor will bypass this noise while a
tantalum will not. Since the output capacitor is one of the two
external components that control the stability of the regulator
control loop, most applications will require a minimum at 0.47
µF of output capacitance. Like the input capacitor, recom-
mended multilayer ceramic capacitors are X7R or X5R.
Again, verify actual capacitance at the desired operating volt-
age and temperature.
DIODE
The diode (D1) conducts during the switch off time. A Schottky
diode is recommended for its fast switching times and low
forward voltage drop. The diode should be chosen so that its
current rating is greater than:
ID1 ≥ IOUT
The reverse breakdown rating of the diode must be at least
the maximum output voltage plus appropriate margin.
OUTPUT OVER-VOLTAGE PROTECTION
A simple circuit consisting of an external zener diode can be
implemented to protect the output and the LM3410 device
from an over-voltage fault condition. If an LED fails open, or
is connected backwards, an output open circuit condition will
occur. No current is conducted through the LED’s, and the
feedback node will equal zero volts. The LM3410 will react to
this fault by increasing the duty-cycle, thinking the LED cur-
rent has dropped. A simple circuit that protects the LM3410
is shown in figure 6.
Zener diode D2 and resistor R3 is placed from VOUT in parallel
with the string of LEDs. If the output voltage exceeds the
breakdown voltage of the zener diode, current is drawn
through the zener diode, R3 and sense resistor R1. Once the
voltage across R1 and R3 equals the feedback voltage of
190mV, the LM3410 will limit its duty-cycle. No damage will
occur to the LM3410, the LED’s, or the zener diode. Once the
fault is corrected, the application will work as intended.
30038530
FIGURE 6. Overvoltage Protection Circuit
PCB Layout Considerations
When planning layout there are a few things to consider when
trying to achieve a clean, regulated output. The most impor-
tant consideration when completing a Boost Converter layout
is the close coupling of the GND connections of the COUT ca-
pacitor and the LM3410 PGND pin. The GND ends should be
close to one another and be connected to the GND plane with
at least two through-holes. There should be a continuous
ground plane on the bottom layer of a two-layer board except
under the switching node island. The FB pin is a high
impedance node and care should be taken to make the FB
trace short to avoid noise pickup and inaccurate regulation.
The RSET feedback resistor should be placed as close as
possible to the IC, with the AGND of RSET (R1) placed as close
as possible to the AGND (pin 5 for the LLP) of the IC. Radiated
noise can be decreased by choosing a shielded inductor. The
remaining components should also be placed as close as
possible to the IC. Please see Application Note AN-1229 for
further considerations and the LM3410 demo board as an ex-
ample of a four-layer layout.
Below is an example of a good thermal & electrical PCB de-
sign.
30038532
FIGURE 7. Boost PCB Layout Guidelines
This is very similar to our LM3410 demonstration boards that
are obtainable via the National Semiconductor website. The
demonstration board consists of a two layer PCB with a com-
mon input and output voltage application. Most of the routing
is on the top layer, with the bottom layer consisting of a large
ground plane. The placement of the external components
satisfies the electrical considerations, and the thermal perfor-
11 www.national.com
Free Datasheet http://www.datasheet4u.com/
11 Page | ||
| Páginas | Total 32 Páginas | |
| PDF Descargar | [ Datasheet LM3410.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| LM341 | 3-Terminal Positive Voltage Regulators | National Semiconductor |
| LM341 | LM341/LM78MXX Series 3-Terminal Positive Voltage Regulators (Rev. E) |  Texas Instruments |
| LM341-12 | LM341/LM78MXX Series 3-Terminal Positive Voltage Regulators (Rev. E) | Texas Instruments |
| LM341-15 | LM341/LM78MXX Series 3-Terminal Positive Voltage Regulators (Rev. E) | Texas Instruments |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |