AN10145 Datasheet PDF - NXP Semiconductors
| Part Number | AN10145 | |
| Description | Bi-directional low voltage translators | |
| Manufacturers | NXP Semiconductors | |
| Logo |  |
|
|
There is a preview and AN10145 download ( pdf file ) link at the bottom of this page. Total 24 Pages | ||
Preview 1 page No Preview Available !
INTEGRATED CIRCUITS
DREF
GREF
D1
D22
SREF
S1
S22
ABSTRACT
Philips Semiconductors Gunning Transceiver Logic Translator Voltage Clamp (GTL-TVC)
bi-directional low voltage translators are used in bi-directional signaling voltage level translation
applications. Voltage translation can be from any voltage between 1.0 V to 5.0 V to any voltage
between 1.0 V to 5.0 V without need for directional control. Device operation, resistor sizing and
typical applications are discussed in this application note.
AN10145
Bi-directional low voltage translators
GTL2000, GTL2002, GTL2010
Supersedes data of 2002 Dec 16
Alma Anderson – Senior Design Engineer
Jean-Marc Irazabal – Technical Marketing Manager
Steve Blozis – International Product Manager
Specialty Logic Product Line
Interface Products Business Line
2004 Aug 11
Philips
Semiconductors
Free Datasheet http://www.datasheet4u.com/
|
| |
 
Cross-Bar Technology (CBT) Like Behavior
The large NMOS pass transistors used in the GTL-TVC devices are very similar to the large NMOS pass transistors used
in CBT devices. However unlike the CBT devices that use internal drivers to control the gate of the NMOS pass
transistor, the gate pin of the GTL-TVC devices is directly connected to the gate of each transistor. In principle the
GTL-TVC devices can be used like CBT devices except that the gate input capacitance is much larger than a normal
CBT device. When using the GTL-TVC devices as CBT devices, the gate pin (GREF) is driven by external logic to the
power supply, to enable it, or to ground to disable it, and the SREF and DREF pins can be used as an additional channel
as shown in Figure 3.
VDD
Chip set
GTL2002
GND GREF
SREF DREF
S1 D1
S2 D2
Control
5V
VDD
Chipset I/O
Figure 3. Cross Bar Technology like Application
Note: If a 5 V to 3.3 V translation is wanted, best results are achieved using the bias circuit of the GTL-TVC with the
SREF at 3.3 V. Additionally, when used as a CBT function with the gate at VDD and the input at VDD, the maximum pass
voltage will be ~ VDD – 1 V because the output is shifted down by a threshold compared to the gate voltage.
Features
The GTL-TVC family has several features that benefit a system designer when designing an interface between devices
with different I/O voltage levels.
Device Construction – The GTL-TVC devices are of a very simple design. The only required connections are GND,
gate of the reference transistor (GREF), drain of the reference transistor (DREF) and source of the reference transistor
(SREF) and then any of the Dn/Sn I/O pairs needed for voltage level translations.
• Any transistor Dn or Sn I/O pair can be used as the source or drain of the reference transistor (SREF or DREF). This
makes it easier to route signals to and from the device.
• All the transistors are on one die, which is manufactured with very tight process control. This provides a very low
spread of VO relative to SREF or DREF.
• It is easy to change the SREF voltage allowing the system designer an easy migration path to even lower voltages
(e.g. 1.5 V or 1.2 V).
• Dn /Sn I/O pairs are matched on either side of the devices (e.g., flow through pinout) which offers easy trace
routing.
No Active Control Logic – As shown in Figure 4, the GTL-TVC is a passive device and there is no active control logic.
This means there is no supply power (VDD) required for device operation.
Figure 4. GTL20XX Logic Diagram
5
Free Datasheet http://www.datasheet4u.com/
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for AN10145 electronic component. |
| Information | Total 24 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ AN10145.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| AN10145 | The function is Bi-directional low voltage translators. NXP Semiconductors | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
AN10
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||