|
AT24C256C PDF даташит
| Спецификация AT24C256C изготовлена «ATMEL Corporation» и имеет функцию, называемую «2-Wire Serial EEPROM». |
|
|
Детали детали
| Номер произв | AT24C256C |
| Описание | 2-Wire Serial EEPROM |
| Производители | ATMEL Corporation |
| логотип |  |
21 Pages
No Preview Available ! |
AT24C256C
I2C-Compatible (2-Wire) Serial EEPROM
256-Kbit (32,768 x 8)
DATASHEET
Features
Low-voltage and Standard-voltage Operation
̶ VCC = 1.7V to 5.5V
Internally Organized as 32,768 x 8
2-wire Serial Interface
Schmitt Trigger, Filtered Inputs for Noise Suppression
Bidirectional Data Transfer Protocol
400kHz (1.7V) and 1MHz (2.5V, 2.7V, 5.0V) Compatibility
Write Protect Pin for Hardware Protection
64-byte Page Write Mode
̶ Partial Page Writes Allowed
Self-timed Write Cycle (5ms Max)
High Reliability
̶ Endurance: 1,000,000 Write Cycles
̶ Data Retention: 40 Years
Lead-free/Halogen-free Devices Available
Green Package Options (Pb/Halide-free/RoHS Compliant)
̶ 8-lead JEDEC SOIC, 8-lead TSSOP, 8-pad UDFN, and 8-ball VFBGA
Packages
Die Sale Options: Wafer Form, Waffle Pack, and Bumped Wafers
Description
The Atmel® AT24C256C provides 262,144-bits of Serial Electrically Erasable and
Programmable Read-Only Memory (EEPROM) organized as 32,768 words of
8 bits each. The device’s cascading feature allows up to eight devices to share a
common 2-wire bus. The device is optimized for use in many industrial and
commercial applications where low-power and low-voltage operation are
essential. The devices are available in space-saving 8-lead JEDEC SOIC, 8-lead
TSSOP, 8-pad UDFN, and 8-ball VFBGA packages. In addition, this device
operates from 1.7V to 5.5V.
Atmel-8568F-SEEPROM-AT24C256C-Datasheet_012015
No Preview Available ! |
1. Pin Configurations and Pinouts
Table 1-1.
Pin
A0
A1
A2
GND
SDA
SCL
WP
VCC
Pin Configuration
Function
Address Input
Address Input
Address Input
Ground
Serial Data
Serial Clock Input
Write Protect
Device Power Supply
A0
A1
A2
GND
8-lead SOIC
18
27
36
45
Top View
VCC
WP
SCL
SDA
8-pad UDFN
A0 1
A1 2
A2 3
GND 4
8 VCC
7 WP
6 SCL
5 SDA
Top View
A0
A1
A2
GND
8-lead TSSOP
18
27
36
45
Top View
VCC
WP
SCL
SDA
8-ball VFBGA
VCC 8
WP 7
SCL 6
SDA 5
1 A0
2 A1
3 A2
4 GND
Bottom View
2. Absolute Maximum Ratings*
Operating Temperature . . . . . . . . . . .-55°C to +125°C
Storage Temperature . . . . . . . . . . . -65°C to + 150°C
Voltage on any pin
with respect to ground . . . . . . . . . . . . . . . -1.0 V +7.0V
Maximum Operating Voltage . . . . . . . . . . . . . . . 6.25V
DC Output Current . . . . . . . . . . . . . . . . . . . . . . .5.0mA
*Notice: Stresses beyond those listed under “Absolute
Maximum Ratings” may cause permanent damage
to the device. This is a stress rating only and
functional operation of the device at these or any
other conditions beyond those indicated in the
operational sections of this specification are not
implied. Exposure to absolute maximum rating
conditions for extended periods may affect device
reliability.
2 AT24C256C [DATASHEET]
Atmel-8568F-SEEPROM-AT24C256C-Datasheet_012015
No Preview Available ! |
3. Block Diagram
VCC
GND
WP
SCL
SDA
A2
A1
A0
Start
Stop
Logic
LOAD
Device
Address
Comparator
R/W
Serial
Control
Logic
COMP
LOAD INC
Data Word
Addr/Counter
EN H.V. Pump/Timing
Data Recovery
EEPROM
DIN
DOUT
Y DEC
Serial MUX
DOUT/ACK
LOGIC
4. Pin Descriptions
Serial Clock (SCL): The SCL input is used to positive-edge clock data into each EEPROM device and negative-
edge clock data out of each device.
Serial Data (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open drain driven and may be
wire-ORed with any number of other open-drain or open-collector devices.
Device Addresses (A2, A1, A0): The A2, A1, and A0 pins are device address inputs that are hard wired (directly to
GND or to VCC) for compatibility with other Atmel AT24C devices. When the pins are hard wired, as many as eight
256K devices may be addressed on a single bus system. (Device addressing is discussed in detail in Section 7.
“Device Addressing” on page 9). A device is selected when a corresponding hardware and software match is true.
If these pins are left floating, the A2, A1, and A0 pins will be internally pulled down to GND. However, due to
capacitive coupling that may appear during customer applications, Atmel recommends always connecting the
address pins to a known state. When using a pull-up resistor, Atmel recommends using 10k or less.
Write Protect (WP): The Write Protect input, when connected to GND, allows normal write operations. When WP
is connected directly to VCC, all write operations to the memory are inhibited. If the pin is left floating, the WP pin
will be internally pulled down to GND. However, due to capacitive coupling that may appear during customer
applications, Atmel recommends always connecting the WP pins to a known state. When using a pull-up resistor,
Atmel recommends using 10k or less.
Table 4-1. Write Protect
WP Pin Status
At VCC
At GND
Part of the Array Protected
Full Array
Normal Read/Write Operations
AT24C256C [DATASHEET]
Atmel-8568F-SEEPROM-AT24C256C-Datasheet_012015
3
Скачать PDF:
[ AT24C256C.PDF Даташит ]
| Номер в каталоге | Описание | Производители |
| AT24C256 | 2-Wire Serial EEPROMs | ATMEL Corporation |
| AT24C256B | Two-wire Serial EEPROM 256K | ATMEL Corporation |
| AT24C256C | 2-Wire Serial EEPROM | ATMEL Corporation |
| Номер в каталоге | Описание | Производители |
| TL431 | 100 мА, регулируемый прецизионный шунтирующий регулятор |
 Unisonic Technologies |
| IRF840 | 8 А, 500 В, N-канальный МОП-транзистор |
 Vishay |
| LM317 | Линейный стабилизатор напряжения, 1,5 А |
 STMicroelectronics |
|
DataSheet26.com | 2020 | Контакты | Поиск |