DataSheet26.com

IR21141SSPBF PDF даташит

Спецификация IR21141SSPBF изготовлена ​​​​«International Rectifier» и имеет функцию, называемую «(IR2114SSPBF - IR22141SSPBF) HALF-BRIDGE GATE DRIVER IC».

Детали детали

Номер произв IR21141SSPBF
Описание (IR2114SSPBF - IR22141SSPBF) HALF-BRIDGE GATE DRIVER IC
Производители International Rectifier
логотип International Rectifier логотип 

33 Pages
scroll

No Preview Available !

IR21141SSPBF Даташит, Описание, Даташиты
Data Sheet No. PD60213 revG
IR2114SSPbF/IR21141SSPbF
IR2214SSPbF/IR22141SSPbF
HALF-BRIDGE GATE DRIVER IC
Features
Floating channel up to +600 V or +1200 V
Soft over-current shutdown
Synchronization signal to synchronize shutdown with the other phases
Integrated desaturation detection circuit
Two stage turn on output for di/dt control
Separate pull-up/pull-down output drive pins
Matched delay outputs
Undervoltage lockout with hysteresis band
LEAD-FREE
Description
The IR211(4,41)/IR221(4,41) gate driver family is suited to drive a single half
bridge in power switching applications. These drivers provide high gate driving
capability (2 A source, 3 A sink) and require low quiescent current, which allows
the use of bootstrap power supply techniques in medium power systems. These
drivers feature full short circuit protection by means of power transistor
desaturation detection and manage all half-bridge faults by smoothly turning off
the desaturated transistor through the dedicated soft shutdown pin, therefore
preventing over-voltages and reducing EM emissions. In multi-phase systems,
the IR211(4,41)/ IR221(4,41) drivers communicate using a dedicated local
network (SY_FLT and FAULT/SD signals) to properly manage phase-to-phase
short circuits. The system controller may force shutdown or readwww.DataSheet.co.kr device fault
state through the 3.3 V compatible CMOS I/O pin (FAULT/SD). To improve the
signal immunity from DC-bus noise, the control and power ground use dedicated
pins enabling low-side emitter current sensing as well. Undervoltage conditions
in floating and low voltage circuits are managed independently.
Product Summary
VOFFSET
IO+/- (min)
VOUT
Deadtime matching (max)
Deadtime (typ)
Desat blanking time (typ)
DSH, DSL input voltage
threshold (typ)
Soft shutdown time (typ)
600 V or
1200 V max.
1.0 A / 1.5 A
10.4 V – 20 V
75 ns
330 ns
3 µs
8.0 V
9.25 µs
Package
24-Lead SSOP
Typical connection
DC+
15 V
DC BUS
uP,
(Up to 1200 V) Control
VCC
LIN
HIN
FAULT/SD
FLT_CLR
SY_ F LT
VSS
VB
HOP
HON
SSDH
DSH
VS
LOP
LON
SSDL
DSL
COM
Motor
DC-
www.irf.com
1
Datasheet pdf - http://www.DataSheet4U.net/









No Preview Available !

IR21141SSPBF Даташит, Описание, Даташиты
IR211(4,41)/IR221(4,41)SSPbF
Absolute Maximum Ratings
Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage
parameters are absolute voltages referenced to VSS, all currents are defined positive into any lead The thermal resistance
and power dissipation ratings are measured under board mounted and still air conditions.
Symbol
Definition
Min.
Max. Units
VS
VB
VHO
VCC
COM
VLO
VIN
VFLT
VDSH
VDSL
dVs/dt
High side offset voltage
High side floating supply voltage
(IR2114 or IR21141)
(IR2214 or IR22141)
High side floating output voltage (HOP, HON and SSDH)
Low side and logic fixed supply voltage
Power ground
Low side output voltage (LOP, LON and SSDL)
Logic input voltage (HIN, LIN and FLT_CLR)
www.DataSheet.co.kr
FAULT input/output voltage (FAULT/SD and SY_FLT)
High side DS input voltage
Low side DS input voltage
Allowable offset voltage slew rate
VB - 25
-0.3
-0.3
VS - 0.3
-0.3
VCC - 25
VCOM -0.3
VSS -0.3
VSS -0.3
VS -3
VCOM -3
VB + 0.3
625
1225
VB + 0.3
25
VCC + 0.3
VCC + 0.3
VCC + 0.3
VCC + 0.3
VB + 0.3
VCC + 0.3
50
V
V/ns
PD
RthJA
TJ
TS
TL
Package power dissipation @ TA 25 °C
Thermal resistance, junction to ambient
Junction temperature
Storage temperature
Lead temperature (soldering, 10 seconds)
— 1.5 W
— 65 °C/W
— 150
-55 150 °C
— 300
Recommended Operating Conditions
For proper operation the device should be used within the recommended conditions. All voltage parameters are absolute
voltages referenced to VSS. The VS offset rating is tested with all supplies biased at a 15 V differential.
Symbol
Definition
Min.
Max. Units
VB High side floating supply voltage (Note 1)
VS
High side floating supply offset
voltage
(IR2114 or IR21141)
(IR2214 or IR22141)
VS + 11.5
Note 2
Note 2
VS + 20
600
1200
VHO High side output voltage (HOP, HON and SSDH)
VS VS + 20
VLO Low side output voltage (LOP, LON and SSDL)
VCOM
VCC
VCC Low side and logic fixed supply voltage (Note 1)
11.5 20
COM
Power ground
-5 5
VIN Logic input voltage (HIN, LIN and FLT_CLR)
VFLT Fault input/output voltage (FAULT/SD and SY_FLT)
VSS
VSS
VCC
VCC
VDSH
High side DS pin input voltage
VS - 2.0
VB
VDSL
Low side DS pin input voltage
VCOM - 2.0
VCC
TA Ambient temperature
-40 125
Note 1: While internal circuitry is operational below the indicated supply voltages, the UV lockout disables
the output drivers if the UV thresholds are not reached.
Note 2: Logic operational for VS from VSS-5 V to VSS +600 V or 1200 V. Logic state held for VS from VSS -5 V
to VSS-VBS. (Please refer to the Design Tip DT97-3 for more details).
V
°C
Datasheet pdf - http://www
www.irf.com
2









No Preview Available !

IR21141SSPBF Даташит, Описание, Даташиты
IR211(4,41)/IR221(4,41)SSPbF
Static Electrical Characteristics
VCC = 15 V, VSS = COM = 0 V, VS = 600 V or 1200 V and TA = 25 °C unless otherwise specified.
Pins: VCC, VSS, VB, VS
Symbol
Definition
VCCUV+
VCCUV-
VCCUVH
VBSUV+
VBSUV-
VBSUVH
VCC supply undervoltage positive going threshold
VCC supply undervoltage negative going threshold
VCC supply undervoltage lockout hysteresis
(VB-VS) supply undervoltage positive going threshold
(VB-VS) supply undervoltage negative going threshold
(VB-VS) supply undervoltage lockout hysteresis
ILK Offset supply leakage current
IQBS Quiescent VBS supply current
IQCC Quiescent VCC supply current
Note 1: Refer to Fig. 1
Min Typ Max Units Test Conditions
9.3 10.2 11.4
8.7 9.3 10.3
— 0.9 —
V
9.3 10.2 11.4
VS = 0 V, VS = 600 V
8.7 9.3 10.3
or 1200 V
— 0.9 —
— — 50 µA
— 400 800
VB = VS = 600 V or
1200 V
VIN = 0 V or 3.3 V
— 0.7 2.5 mA
(No load)
Pins: HIN, LIN, FLTCLR, FAULT/SD, SY_FLT
Symbol
Definition
VIH Logic "1" input voltage
VIL Logic "0" input voltage
VIHSS Logic input hysteresis
IIN+
Logic “1” input bias current (HIN, LIN, FLTCLR)
Logic “0” input bias current (FAULT/SD, SY_FLT)
www.DataSheet.co.kr
IIN-
Logic “0” input bias current
Logic “1” input bias current (FAULT/SD, SY_FLT)
RON,FLT
RON,SY
FAULT/SD open drain resistance
SY_FLT open drain resistance
Note 1: Refer to Figs. 2 & 3
Min Typ
2.0 —
——
0.2 0.4
— 330
0—
-1 —
-1 —
— 60
— 60
Max Units
0.8 V
1 µA
0
0
Test Conditions
VCC = VCCUV-
to 20 V
VIN = 3.3 V
VIN = 0 V
PW7 µs
Pins: DSL, DSH
The active bias is present only the IR21141and IR22141. VDESAT, IDS and IDSB parameters are referenced to COM and VS
respectively for DSL and DSH.
Symbol
Definition
Min Typ Max Units
Test Conditions
VDESAT+
High desat input threshold voltage
VDESAT-
Low desat input threshold voltage
VDSTH
Desat input voltage hysteresis
IDS+ High DSH or DSL input bias current
IDS- Low DSH or DSL input bias current
IDSB
DSH or DSL input bias current
(IR21141 and IR22141 only)
Note 1: Refer to Fig. 4
7.2 8.0 8.8
6.3 7.0 7.7
— 1.0 —
— 21 —
— -160 —
— -20 —
V
µA
mA
See Figs. 4,16
VDESAT = VCC or VBS
VDESAT = 0 V
VDESAT = (VCC or VBS) – 2 V
www.irf.com
3
Datasheet pdf - http://www.DataSheet4U.net/










Скачать PDF:

[ IR21141SSPBF.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
IR21141SSPBFHALF-BRIDGE GATE DRIVER ICInternational Rectifier
International Rectifier
IR21141SSPBF(IR2114SSPBF - IR22141SSPBF) HALF-BRIDGE GATE DRIVER ICInternational Rectifier
International Rectifier

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск