|
|
Número de pieza | LTM4607 | |
Descripción | 24VOUT High Efficiency Buck-Boost DC/DC uModule | |
Fabricantes | Linear Technology | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de LTM4607 (archivo pdf) en la parte inferior de esta página. Total 24 Páginas | ||
No Preview Available ! www.DataSheet4U.com
LTM4607
36VIN, 24VOUT High Efficiency
Buck-Boost DC/DC µModule
FEATURES
■ Single Inductor Architecture Allows VIN Above,
Below or Equal to VOUT
■ Wide VIN Range: 4.5V to 36V
■ Wide VOUT Range: 0.8V to 24V
■ 5A DC (10A DC in Buck Mode)
■ High Efficiency Up to 98%
■ Current Mode Control
■ Power Good Output Signal
■ Phase-Lockable Fixed Frequency: 200kHz to 400kHz
■ Ultra-Fast Transient Response
■ Current Foldback Protection
■ Output Overvoltage Protection
■ Small, Low Profile Surface Mount LGA Package
(15mm × 15mm × 2.8mm)
APPLICATIONS
■ Telecom, Servers and Networking Equipment
■ Industrial and Automotive Equipment
■ High Power Battery-Operated Devices
DESCRIPTION
The LTM®4607 is a high efficiency switching mode buck-
boost power supply. Included in the package are the
switching controller, power FETs, and support components.
Operating over an input voltage range of 4.5V to 36V, the
LTM4607 supports an output voltage range of 0.8V to
24V, set by a resistor. This high efficiency design delivers
up to 5A continuous current in boost mode (10A in buck
mode). Only the inductor, sense resistor, bulk input and
output capacitors are needed to finish the design.
The low profile package enables utilization of unused space
on the bottom of PC boards for high density point of load
regulation. The high switching frequency and current
mode architecture enable a very fast transient response
to line and load changes without sacrificing stability. The
LTM4607 can be frequency synchronized with an external
clock to reduce undesirable frequency harmonics.
Fault protection features include overvoltage and foldback
current protection. The DC/DC μModule™ is offered in a
small thermally enhanced 15mm × 15mm × 2.8mm LGA
package. The LTM4607 is Pb-free and RoHS compliant.
, LT, LTC, LTM and Burst Mode are registered trademarks of Linear Technology
Corporation. μModule is a trademark of Linear Technology Corporation. All other
trademarks are the property of their respective owners.
TYPICAL APPLICATION
20V/2.5A Buck-Boost DC/DC μModule with 4.5V to 36V Input
VIN
4.5V TO 36V
10μF
50V
ON/OFF
0.1μF
CLOCK SYNC
VIN PLLIN VOUT
FCB
RUN LTM4607
SW1
SW2
RSENSE
SENSE+
SS
SGND
SENSE–
PGND
VFB
4.7μH
R2
7mΩ
4.12k
10μF +
35V
330μF
25V
VOUT
20V
2.5A
4607 TA01
Efficiency and Power Loss vs
Input Voltage
100
6
99
98 5
97 4
96
95 3
94
2
93
92 1
91 VOUT = 20V, 2.5A
f = 200kHz
90 0
6 11 16 21 26 31 36
VIN (V)
4607 TA01b
4607f
1
1 page www.DataSheet4U.com
TYPICAL PERFORMANCE CHARACTERISTICS (Refer to Figure 18)
LTM4607
Efficiency vs Load Current
6VIN to 12VOUT
100
90
80
70
60
50
40
30
20
10
0
0.01
0.1 1
LOAD CURRENT (A)
BURST
DCM
CCM
10
4607 G01
Efficiency vs Load Current
12VIN to 12VOUT
100
90
80
70
60
50
40
30
20
10
0
0.01
0.1 1
LOAD CURRENT (A)
BURST
DCM
CCM
10
4607 G02
Efficiency vs Load Current
32VIN to 12VOUT
100
90
80
70
60
50
40
30
20
10
0
0.01
SKIP CYCLE
DCM
CCM
0.1 1 10
LOAD CURRENT (A)
100
4607 G03
Efficiency vs Load Current
3.3μH Inductor
100
95
90
85
80
75
70
0
5VIN TO 5VOUT
12VIN TO 5VOUT
32VIN TO 5VOUT
2 4 6 8 10 12
LOAD CURRENT (A)
4607 G04
Efficiency vs Load Current
6μH Inductor
100
99
98
97
96
95
94
93
92
91
90
0
28VIN to 20VOUT
32VIN to 20VOUT
36VIN to 20VOUT
246
LOAD CURRENT (A)
8
4607 G05
Efficiency vs Load Current
8μH Inductor
100
99
98
97
96
95
94
93
92 28VIN to 24VOUT
91 32VIN to 24VOUT
36VIN to 24VOUT
90
012 34 56 7
LOAD CURRENT (A)
4607 G06
Efficiency vs Load Current
100
Transient Response from
6VIN to 12VOUT
Transient Response from
12VIN to 12VOUT
95
90
85
80
75
70
0
IOUT
2A/DIV
VOUT
200mV/DIV
5VIN to 16VOUT
5VIN to 20VOUT
5VIN to 24VOUT
0.5 1 1.5 2 2.5
LOAD CURRENT (A)
3
4607 G06a
200μs/DIV
4607 G07
LOAD STEP: 0A TO 3A AT CCM
OUTPUT CAPS: 4x 22μF CERAMIC CAPS AND
2x 180μF ELECTROLYTIC CAPS
2x 15mΩ SENSING RESISTORS
IOUT
2A/DIV
VOUT
200mV/DIV
200μs/DIV
4607 G08
LOAD STEP: 0A TO 3A AT CCM
OUTPUT CAPS: 4x 22μF CERAMIC CAPS AND
2x 180μF ELECTROLYTIC CAPS
2x 15mΩ SENSING RESISTORS
4607f
5
5 Page www.DataSheet4U.com
LTM4607
APPLICATIONS INFORMATION
ings are often based on temperature and hours of life. This
makes it advisable to properly derate the input capacitor,
or choose a capacitor rated at a higher temperature than
required. Always contact the capacitor manufacturer for
derating requirements.
Output Capacitors
In boost mode, the discontinuous current shifts from the
input to the output, so the output capacitor COUT must be
capable of reducing the output voltage ripple.
For boost and buck modes, the steady ripple due to charg-
ing and discharging the bulk capacitance is given by:
( )VRIPPLE,BOOST
=
IOUT(MAX) •
COUT
VOUT − VIN(MIN)
• VOUT • f
( )VRIPPLE,BUCK
=
VOUT
8 •L •
• VIN(MAX) − VOUT
COUT • VIN(MAX) • f2
The steady ripple due to the voltage drop across the ESR
(effective series resistance) is given by:
VESR,BUCK = ΔIL(MAX) • ESR
VESR,BOOST = IL(MAX) • ESR
The LTM4607 is designed for low output voltage ripple.
The bulk output capacitors defined as COUT are chosen
with low enough ESR to meet the output voltage ripple and
transient requirements. COUT can be the low ESR tantalum
capacitor, the low ESR polymer capacitor or the ceramic
capacitor. Multiple capacitors can be placed in parallel to
meet the ESR and RMS current handling requirements. The
typical capacitance is 300μF. Additional output filtering may
be required by the system designer, if further reduction of
output ripple or dynamic transient spike is required. Table
3 shows a matrix of different output voltages and output
capacitors to minimize the voltage droop and overshoot
at a current transient.
Inductor Selection
The inductor is chiefly decided by the required ripple cur-
rent and the operating frequency. The inductor current
ripple ΔIL is typically set to 20% to 40% of the maximum
inductor current. In the inductor design, the worst cases
in continuous mode are considered as follows:
( )LBOOST
≥
VIN •
VOUT(MAX)
VOUT(MAX) −
• f •IOUT(MAX)
VIN
• Ripple%
( )LBUCK
≥
VOUT •
VIN(MAX) • f
VIN(MAX) −
• IOUT(MAX)
VOUT
• Ripple%
where:
f is operating frequency, Hz
Ripple% is allowable inductor current ripple, %
VOUT(MAX) is maximum output voltage, V
VIN(MAX) is maximum input voltage, V
VOUT is output voltage, V
IOUT(MAX) is maximum output load current, A
The inductor should have low DC resistance to reduce the
I2R losses, and must be able to handle the peak inductor
current without saturation. To minimize radiated noise,
use a toroid, pot core or shielded bobbin inductor. Please
refer to Table 3 for the recommended inductors for dif-
ferent cases.
RSENSE Selection and Maximum Output Current
RSENSE is chosen based on the required inductor current.
Since the maximum inductor valley current at buck mode
is much lower than the inductor peak current at boost
mode, different sensing resistors are suggested to use
in buck and boost modes.
The current comparator threshold sets the peak of the
inductor current in boost mode and the maximum inductor
valley current in buck mode. In boost mode, the allowed
maximum average load current is:
IOUT(MAX,BOOST)
=
160mV
RSENSE
IL
2
•
VIN
VOUT
where ΔIL is peak-to-peak inductor ripple current.
4607f
11
11 Page |
Páginas | Total 24 Páginas | |
PDF Descargar | [ Datasheet LTM4607.PDF ] |
Número de pieza | Descripción | Fabricantes |
LTM4600 | High Efficiency DC/DC Module | Linear Technology |
LTM4600HV | High Efficiency DC/DC uModule | Linear Technology |
LTM4601 | step-down switch mode DC/DC power supply | Linear Technology |
LTM4601-1 | step-down switch mode DC/DC power supply | Linear Technology |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |