DataSheet26.com

715P PDF даташит

Спецификация 715P изготовлена ​​​​«Vishay Siliconix» и имеет функцию, называемую «Polypropylene Film Capacitors ORANGE DROP».

Детали детали

Номер произв 715P
Описание Polypropylene Film Capacitors ORANGE DROP
Производители Vishay Siliconix
логотип Vishay Siliconix логотип 

7 Pages
scroll

No Preview Available !

715P Даташит, Описание, Даташиты
www.DataSheet4U.com
Polypropylene Film Capacitors
ORANGE DROP®, Low Loss
Type 715P
Vishay Sprague
PERFORMANCE CHARACTERISTICS
Operating Temperature: - 55°C to + 85°C standard; up to
+ 105°C when working voltage is reduced to 50% of the
+ 85°C rating.
Insulation Resistance: After a 2 minute charge at rated
voltage or 500 V, whichever is less.
At + 25°C: 400,000 Megohm for C .5µF.
200,000 Megohm - Microfarads for C > .5 Microfarads.
At + 85°C: 20,000 Megohm for C .5 Microfarads.
10,000 Megohm - Microfarads for C > .5 Microfarads.
At + 105°C: 2000 Megohm for C .5µF.
1000 Megohm - Microfarads for C > .5 Microfarads.
Capacitance, Tolerance and Dissipation Factor:
Capacitors shall be measured at a frequency of 1000Hz
at + 25°C or else be referred to measurements made at
that frequency and temperature. The maximum dissipation
factor shall be 0.1%.
Dielectric Withstanding Voltage: Capacitors rated below
1000 volts shall withstand a DC potential of 250% of rated
voltage applied between terminals for not more than
5 seconds. Capacitors rated 1000 volts and above shall
withstand a DC potential of 200% of rated voltage applied
between the terminals for not more than 5 seconds. The
test voltage must be applied and discharged through a
resistor of one ohm per volt.
Polypropylene plastic film is employed as the dielectric in Type
715P ORANGE DROP® capacitors. Type 715P capacitors
are ideal for applications where high AC current flow is found,
as in certain solid-state TV vertical circuits,
r-f generators and pulse-forming networks where dielectric
heating is often a problem.
The polypropylene dielectric film is similar to polystyrene in
that it can handle high AC currents due to its low loss but with
the added advantage of an operating temperature to
+ 105°C.
Capacitance change with temperature is less than 3% over
the entire operating temperature range. The temperature
coefficient is negative and virtually linear at 180PPM/°C over
the temperature range of + 25°C to + 105°C. This characteristic
means the Type 715P is suitable for matching with positive TC
resistors and inductors to maintain circuit stability.
Type 715P ORANGE DROP® capacitors are conformally
coated with a flame retardant epoxy.
Performance characteristics, as well as curves showing typical
variation in electrical characteristics as a function of temperature
and frequency, are given.
Humidity Test: Condition capacitors with no voltage
applied for 72 hours at 95% relative humidity and + 75°C.
Remove capacitors from humidity chamber, wipe surface
dry of moisture and dry in circulating air for 4 hours.
Measure insulation resistance after a two minute charge at
+ 25°C and rated voltage or 500 VDC, whichever is less.
Minimum product of insulation resistance and capacitance
shall be 50,000 Megohm-microfarads after test but need
not exceed 100,000 Megohm. Not more than one failure
in 12 units tested shall be permitted.
DC Life Test: Capacitors are capable of withstanding a
500 hour life test at + 85°C at 150% of rated working
voltage. After test, capacitance shall not have changed by
more than 5% of initial value, insulation resistance shall
not have decreased by more than 50% of the initial limit
and dissipation factor shall not have increased to more
than 0.1%.
AC Life Test: Capacitors shall withstand the maximum
60Hz voltage for a period of 500 hours at + 85°C.
Rated DC Voltage
200
400, 600
800, 1200, 1600
Maximum 60Hz Voltage
155
200
500
Not more than one failure allowed in 12 units tested.
Document Number: 42018
Revision 13-Nov-03
For technical questions, contact [email protected]
www.vishay.com
47









No Preview Available !

715P Даташит, Описание, Даташиты
Type 715P
Vishay Sprague
DIMENSIONS in inches [millimeters]
L
Max.
1.250
[31.750]
Min.
0.250
[6.350]
Max.
L
Max.
Lead
Length
0.250
[6.350]
Max.
L
Max.
Lead
Length
0.250
[6.350]
Max.
D
Max.
S
Terminal A
CASE
CODE
J
K
L
M
L
(Max.)
0.75 [19.050]
0.95 [24.130]
1.30 [33.020]
1.70 [43.180]
S
Terminal B
Terminal A
± 0.060 [1.524]
0.500 [12.700]
0.688 [17.475]
1.031 [26.187]
1.406 [35.712]
S
Terminal D
S
Terminal B
± 0.030 [0.762]
0.500 [12.700]
0.688 [17.475]
0.969 [24.613]
1.344 [34.138]
0.032 [0.813] Dia.
(No. 20 AWG)
Tinned Copper-Clad Steel
Terminal D
± 0.030 [0.762]
0.375 [9.525]
0.375 [9.525]
0.719 [18.263]
1.094 [27.788]
PERFORMANCE CHARACTERISTICS
+2
+1
0
-1
-2
- 55
- 50
TYPICAL
- 25 0 + 25 + 50
+ 85 + 105 + 125
+ 75 + 100
TEMPERATURE DEG. CENTIGRADE
0.075
0.05
0.025
0
- 55
- 50
1000
TYPICAL
- 25 0 + 25 + 50
+ 85 + 105 + 125
+ 75 + 100
TEMPERATURE DEG. CENTIGRADE
5
2
155
100
5
2 200 V
.47µF .082µF
.012µF
.039µF
10
1
2
5 10 2
5 100 2 5 1000
FREQUENCY - kHz
10-2
5
2
10-3
5
2
10-4
1
2
TYPICAL
5 10 2
5 100 2
TEMPERATURE DEG. CENTIGRADE
5
1000
1000
5
200
100
5
2 400 V
.0039µF
.47µF .18µF .018µF
10
1
2
5 10 2
5 100 2 5 1000
FREQUENCY - kHz
www.vishay.com
48
For technical questions, contact [email protected]
Document Number: 42018
Revision 13-Nov-03









No Preview Available !

715P Даташит, Описание, Даташиты
Type 715P
Vishay Sprague
PERFORMANCE CHARACTERISTICS
1000
5
200
100
5
2
10
1
1000
600 V
.22µF .027µF
.0082µF
.12µF
2 5 10 2
5 100 2 5 1000
FREQUENCY - kHz
475
2
100
5
.027µF
.047.0µ0F82µ.0F027µ.F0.01053µ9FµF
2
1200 V
10
1
2
5 10 2
5 100 2 5 1000
FREQUENCY - kHz
1000
450
200
100
.056µF
.018µF
.1µF
.0056µF
5
2 800 V
10
12
1000
5 10 2
5 100 2 5 1000
FREQUENCY - kHz
500
2
.033µF
.01µF .0018µF
100 .0056µF
5 .018µF
2
1600 V
10
1
2
5 10 2
5 100 2 5 1000
FREQUENCY - kHz
STANDARD RATINGS* in inches [millimeters]
µF
± 10% TOLERANCE
PART NUMBER
200 VDC/155 VAC**
L
SIZE
D
.012
715P12392J
0.75 [19.05]
0.37 [9.40]
.015
715P15392J
0.75 [19.05]
0.37 [9.40]
.018
715P18392J
0.75 [19.05]
0.37 [9.40]
.022
715P22392J
0.75 [19.05]
0.37 [9.40]
.027
715P27392J
0.75 [19.05]
0.42 [10.67]
.033
715P33392J
0.75 [19.05]
0.42 [10.67]
.039
715P39392K
0.95 [24.13]
0.40 [10.16]
.047
715P47392K
0.95 [24.13]
0.40 [10.16]
.056
715P56392K
0.95 [24.13]
0.45 [11.43]
.068
715P68392K
0.95 [24.13]
0.45 [11.43]
.082
715P82392L
1.30 [33.02]
0.45 [11.43]
.1
715P10492L
1.30 [33.02]
0.45 [11.43]
.12
715P12492L
1.30 [33.02]
0.55 [13.97]
.15
715P15492L
1.30 [33.02]
0.55 [13.97]
.18
715P18492L
1.30 [33.02]
0.62 [15.75]
.22
715P22492L
1.30 [33.02]
0.62 [15.75]
.27
715P27492M
1.70 [43.18]
0.65 [16.51]
.33
715P33492M
1.70 [43.18]
0.65 [16.51]
.39
715P39492M
1.70 [43.18]
0.75 [19.05]
.47
715P47492M
1.70 [43.18]
0.75 [19.05]
* Shaded items, when ordered as ± 5% tolerance with D3 leads, are standard capacitors in stock and available through the Sprague® Distribution
Network. To complete the Type 715P Part Number, add the "D3" suffix and change the capacitance tolerance code number from a "9" to a "5"
to indicate ± 5% (i.e., 715P10456LD3). Any other Part Number, value or type may easily be ordered as a Special.
** 60Hz rms.
Document Number: 42018
Revision 13-Nov-03
For technical questions, contact [email protected]
www.vishay.com
49










Скачать PDF:

[ 715P.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
7150-130mA Low Power LDOHoltek
Holtek
7151Submicro Axial Lead Lamp/Micro Axial Lead Lamps/Axial Lead LampsGilway Technical Lamp
Gilway Technical Lamp
7153T- Subminiature LampsGilway Technical Lamp
Gilway Technical Lamp
7154Submicro Axial Lead Lamp/Micro Axial Lead Lamps/Axial Lead LampsGilway Technical Lamp
Gilway Technical Lamp

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск