|
|
PDF MN101D07G Data sheet ( Hoja de datos )
| Número de pieza | MN101D07G | |
| Descripción | MN101D07x | |
| Fabricantes | Panasonic Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MN101D07G (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
|
No Preview Available !
www.DataSheet4U.com
MN101D07G, MN101D07H
Type
Internal ROM type
ROM (byte)
RAM (byte)
Package (Lead-free)
Minimum Instruction
Execution Time
MN101D07G
MN101D07H
Mask ROM
128K
160K
4K 5K
LQFP112-P-2020
[With main clock operated]
0.1397 µs (at 4.0 V to 5.5 V, 14.32 MHz)
71.5 µs (at 3.0 V to 5.5 V, 14.32 MHz internal frequency di Vision)
[When sub-clock operated]
61 µs (at 2.2 V to 5.5 V, 32.768 kHz)
MN101DF07Z
FLASH
224K
6K
0.1397 µs (at 4.0 V to 5.5 V,14.32 MHz)
71.5 µs (at 3.0 V to 5.5 V, 14.32 MHz
internal frequency di Vision)
61 µs (at 2.5 V to 5.5 V, 32.768 kHz)
Interrupts
RESET, Runaway, External 0 to 4, key input (P50 to P54), Timer 0 to 4, Timer 6, Timer 7, Capstan FG, Control, HSW,
Cylinder(Drum) FG, Servo V-sync, Synchronous output, OSD, XDS, Serial 0 to 2, A/D (common with PWM 4 reference frequency),
OSD V-sync
Timer Counter
Timer counter 0 : 16-bit × 1
(timer function, clock function [max. 2 s or max. 36 h at cascade-connecting with timer 6])
Clock source................ 1/2, (1/4,) 1/8, (1/16) of system clock frequency; overflow of timer counter 6; 1/512 of XI oscillation
clock or OSC oscillation clock frequency
Interrupt source ........... overflow of timer counter 0
Timer counter 1 : 16-bit × 1 (timer function, linear timer counter function)
Clock source................ 1/2, (1/4,) 1/8, (1/16) of system clock frequency; CTL signal
Interrupt source ........... overflow of timer counter 1
www.DataSheet4U.comTimer counter 2 : 16-bit × 1
(timer function, input capture
(DCTL specified edge), duty judgment of DCTL signal)
Clock source................ 1/2, (1/4,) 1/8, (1/16,) 1/12, (1/24) of system clock frequency
Interrupt source ........... overflow of timer counter 2; input of DCTL specified edge; underflow of timer 2 shift register 4-bit
counter; coincidence of timer 2 shift register with timer 2 shift register compare register
Timer counter 3 : 16-bit × 1
(timer function, detection of serial indexing, generation of remote control output carrier frequency)
Clock source................ 1/2, (1/4,) 1/8, (1/16) of system clock frequency; XI oscillation clock
Interrupt source ........... overflow of timer counter 3
Timer counter 4 : 16-bit × 1 (timer function, event count [P15 input], generation of serial transmission clock)
Clock source................ 1/8, (1/16) of system clock frequency; external clock input
Interrupt source ........... overflow of timer counter 4; coincidence of timer counter 4 with OCR4
Timer counter 5 : 19-bit × 1 (watchdog, stable oscillation waiting function)
Clock source................ system clock
Watchdog interrupt source... 1/216, 1/219 of timer counter 5 frequency
Clear by stable oscillation ... after 256 counts by timer counter 5 (218 counts of OSC oscillation clock)
Timer counter 6 : 16-bit × 1 (clock function [max. 2 s])
Clock source................ 1/512 of OSC oscillation clock frequency; XI oscillation clock; 1/4, (1/8,) 1/64, (1/128) of system clock
frequency
Interrupt source ........... 1/213, 1/214, 1/215 overflow of timer counter 6
Timer counter 7 : 8-bit × 1 or 4-bit × 2 (timer function, event count)
Clock source................ 1/4, (1/8,) 1/16, (1/32) of system clock frequency; external clock input
Interrupt source ........... overflow of timer counter 7 (although when 4-bit × 2, there is one interrupt vector. )
DataSheet4 U .com
MAD00030GEM
www.DataSheet4U.com
1 page  
www.DataSheet4U.com
Request for your special attention and precautions in using the technical information and
semiconductors described in this book
(1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and
regulations of the exporting country, especially, those with regard to security export control, must be observed.
(2) The technical information described in this book is intended only to show the main characteristics and application circuit examples
of the products, and no license is granted under any intellectual property right or other right owned by our company or any other
company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other
company which may arise as a result of the use of technical information described in this book.
(3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office
equipment, communications equipment, measuring instruments and household appliances).
Consult our sales staff in advance for information on the following applications:
– Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support
systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the prod-
ucts may directly jeopardize life or harm the human body.
– Any applications other than the standard applications intended.
(4) The products and product specifications described in this book are subject to change without notice for modification and/or im-
provement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product
Standards in advance to make sure that the latest specifications satisfy your requirements.
(5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions
(operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute
maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any
defect which may arise later in your equipment.
Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure
mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire
or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products.
(6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS,
thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which
damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages.
(7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita
www.DataSheet4U.comElectric Industrial Co., Ltd. Industrial Co., Ltd.
DataSheet4 U .com
www.DataSheet4U.com
5 Page | ||
| Páginas | Total 5 Páginas | |
| PDF Descargar | [ Datasheet MN101D07G.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MN101D07 | MN101 Series microcontroller |  Matsushita Electric |
| MN101D07G | MN101D07x | Panasonic Semiconductor |
| MN101D07H | MN101D07x | Panasonic Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |