EPF6024A Datasheet PDF - Altera Corporation
| Part Number | EPF6024A | |
| Description | (EPF6000 Series) Programmable Logic Device | |
| Manufacturers | Altera Corporation | |
| Logo |  |
|
|
There is a preview and EPF6024A download ( pdf file ) link at the bottom of this page. Total 30 Pages | ||
Preview 1 page No Preview Available !
www.DataSheet4U.com
March 2001, ver. 4.1
®
FLEX 6000
Programmable Logic
Device Family
Data Sheet
Features...
s Provides an ideal low-cost, programmable alternative to high-
volume gate array applications and allows fast design changes
during prototyping or design testing
s Product features
– Register-rich, look-up table- (LUT-) based architecture
– OptiFLEX® architecture that increases device area efficiency
– Typical gates ranging from 5,000 to 24,000 gates (see Table 1)
– Built-in low-skew clock distribution tree
– 100% functional testing of all devices; test vectors or scan chains
are not required
s System-level features
– In-circuit reconfigurability (ICR) via external configuration
device or intelligent controller
– 5.0-V devices are fully compliant with peripheral component
interconnect Special Interest Group (PCI SIG) PCI Local Bus
Specification, Revision 2.2
– Built-in Joint Test Action Group (JTAG) boundary-scan test
(BST) circuitry compliant with IEEE Std. 1149.1-1990, available
without consuming additional device logic
– MultiVoltTM I/O interface operation, allowing a device to bridge
between systems operating at different voltages
– Low power consumption (typical specification less than 0.5 mA
in standby mode)
– 3.3-V devices support hot-socketing
Table 1. FLEX 6000 Device Features
Feature
EPF6010A
EPF6016
EPF6016A
EPF6024A
Typical gates (1)
10,000
16,000
16,000
24,000
mLogic elements (LEs)
880
1,320
1,320
1,960
oMaximum I/O pins
102 204 171 218
.cSupply voltage (VCCINT)
3.3 V
5.0 V
3.3 V
3.3 V
UNote:
t4(1) The embedded IEEE Std. 1149.1 JTAG circuitry adds up to 14,000 gates in addition to the listed typical gates.
ataSheeAltera Corporation
www.DA-DS-F6000-04.1
1
|
| |
 
www.DataSheet4U.com
FLEX 6000 Programmable Logic Device Family Data Sheet
Functional
Description
The FLEX 6000 OptiFLEX architecture consists of logic elements (LEs).
Each LE includes a 4-input look-up table (LUT), which can implement any
4-input function, a register, and dedicated paths for carry and cascade
chain functions. Because each LE contains a register, a design can be easily
pipelined without consuming more LEs. The specified gate count for
FLEX 6000 devices includes all LUTs and registers.
LEs are combined into groups called logic array blocks (LABs); each LAB
contains 10 LEs. The Altera software automatically places related LEs into
the same LAB, minimizing the number of required interconnects. Each
LAB can implement a medium-sized block of logic, such as a counter or
multiplexer.
Signal interconnections within FLEX 6000 devices—and to and from
device pins—are provided via the routing structure of the FastTrack
Interconnect. The routing structure is a series of fast, continuous row and
column channels that run the entire length and width of the device. Any
LE or pin can feed or be fed by any other LE or pin via the FastTrack
Interconnect. See “FastTrack Interconnect” on page 17 of this data sheet
for more information.
Each I/O pin is fed by an I/O element (IOE) located at the end of each row
and column of the FastTrack Interconnect. Each IOE contains a
bidirectional I/O buffer. Each IOE is placed next to an LAB, where it can
be driven by the local interconnect of that LAB. This feature allows fast
clock-to-output times of less than 8 ns when a pin is driven by any of the
10 LEs in the adjacent LAB. Also, any LE can drive any pin via the row and
column interconnect. I/O pins can drive the LE registers via the row and
column interconnect, providing setup times as low as 2 ns and hold times
of 0 ns. IOEs provide a variety of features, such as JTAG BST support,
slew-rate control, and tri-state buffers.
Figure 1 shows a block diagram of the FLEX 6000 OptiFLEX architecture.
Each group of ten LEs is combined into an LAB, and the LABs are
arranged into rows and columns. The LABs are interconnected by the
FastTrack Interconnect. IOEs are located at the end of each FastTrack
Interconnect row and column.
wwAwlter.aDCoarpotraatSionheet4U.com
5
Preview 5 Page |
Part DetailsOn this page, you can learn information such as the schematic, equivalent, pinout, replacement, circuit, and manual for EPF6024A electronic component. |
| Information | Total 30 Pages | |
| Link URL | [ Copy URL to Clipboard ] | |
| Download | [ EPF6024A.PDF Datasheet ] | |
Share Link :
Electronic Components Distributor
|
An electronic components distributor is a company that sources, stocks, and sells electronic components to manufacturers, engineers, and hobbyists. |
| SparkFun Electronics | Allied Electronics | DigiKey Electronics | Arrow Electronics |
| Mouser Electronics | Adafruit | Newark | Chip One Stop |
Featured Datasheets
| Part Number | Description | MFRS |
| EPF6024A | The function is (EPF6000 Series) Programmable Logic Device. Altera Corporation | |
Semiconductors commonly used in industry:
1N4148 |
BAW56 |
1N5400 |
NE555 | | ||
Quick jump to:
EPF6
1N4
2N2
2SA
2SC
74H
BC
HCF
IRF
KA | ||