|
|
PDF PT-L711XU Data sheet ( Hoja de datos )
| Número de pieza | PT-L711XU | |
| Descripción | Quick Start Reference Sheet | |
| Fabricantes | Panasonic | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de PT-L711XU (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
|
No Preview Available !
Quick Start Reference Sheet
Panasonic PT-L711XU
Revision A
NOTE: This one-page document is intended only as a quick reference for installation – please read the
SP Controls Application Note for a complete description of this projector driver prior to installation.
I. Driver Features
1. Input Selection Mapping
Selection 1: VIDEO
Selection 2: S-VIDEO
Selection 3: RGB 1
Selection 4: RGB 2
2. Hidden Function Mapping (Default Configuration)
mUsing the ON button as a shift key, press the following buttons to access the specified projector features.
Selection 1: MUTE
oSelection 2: ENTER
Selection 3: ADJUST LEFT
.cSelection 4: ADJUST RIGHT
Off: MENU
Volume Up: ADJUST UP
UVolume Down: ADJUST DOWN
t43. Other Driver Features
Power Status Feedback Method RS-232 Power Polling
eControl Wiring: RS-232 and IR-Emitter
eII. Wiring Specifications
hNOTE: For a wiring diagram, please see the SP Controls Application Note following this document.
S1. RS-232:
Wire the Panel RS-232 port to a male DB9 as follows:
taRX to 2
TX to 3
aGND to 5
Connect this male DB9 to the projector port labeled SERIAL.
.D2. Infrared Emitter:
Wire the Panel IR/Serial port to a female 1/8" Mini as follows:
wIR/SER to tip
GND to ring
wConnect to the included IR Emitter and attach the emitter bud to any projector IR window.
w www.DataSheet4U.comDR-PAN05 1/02/02
SP Controls reserves the right to modify specifications without notice at any time.
1 page  
SmartPanel Projector Driver Application Note
Panasonic PT-L711XU
III. TROUBLESHOOTING
Addition tips can be found in the SmartPanel Configuration and Installation Manual.
The Panel does not completely control the projector..
Full control of the projector requires wiring of both the infrared emiiter and RS-232. Make sure that
RS-232 is correctly connected through Panasonic’s SERIAL port. Also be sure that the IR Emitter bud
is firmly seated on one of the projector IR windows.
The Panel does not do anything at all.
When power is applied to the Panel it should run through a brief power on self-test, during which all of
the Panel lights will turn on and off in sequence. If you do not see this self test, make sure power is
connected correctly and that polarity is correct.
The Panel keeps turning itself off even though the projector is on.
The Panel turns itself off when power polling indicates that the projector is off. Check to make sure the
RS-232 connection is correctly wired (it is extremely unlikely other control would work, and power
polling not).
When I try to turn the projector on, the warming indicator (red LED) blink.
The projector is in the default configured lockout state, and the Panel is waiting for its internal lockout
timer to expire. This feature protects the projector’s bulb. Be sure to let your client know about this
behavior.
IV. TECHNICAL NOTES
1. By default, projector power is verified by polling every few seconds via the RS-232 port. Power polling
can be suspended by depressing and holding the On key; polling will be restored when the key is
released. Should the Panasonic power off, the Panel will usually detect this condition and power off
within thirty seconds. Should the Panasonic power on, the Panel will usually detecting this condition
and power on within ten seconds. Power polling is suspended on the Panasonic during a non-
configurable seventy second lockout following the sending of power off.
2. IR must be wired to control the Panasonic as it does not have a Wired Remote port.
3. The lockout timer specifies the amount of time allowed between sending POWER OFF and POWER
ON to the projector (the delay allows the projector bulbs to cool before re-powering). This delay can
be configured using the Configuration Utility; however, adjusting the lockout timer delay is strongly
discouraged as rapid re-powering causes undue wear on the projector’s bulbs.
V. REVISION HISTORY
1. Revision A (January, 2002)
© 2002 SP Controls Inc. 601 Minnesota Suite 115 San Francisco, CA 94107 [email protected]
5 Page | ||
| Páginas | Total 5 Páginas | |
| PDF Descargar | [ Datasheet PT-L711XU.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| PT-L711XU | Quick Start Reference Sheet | Panasonic |
| PT-L711XU | (PT-L501XU - PT-L711XU) LCD Projector | Panasonic |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |