DataSheet26.com

TSOP1238SB1 PDF даташит

Спецификация TSOP1238SB1 изготовлена ​​​​«Vishay Telefunken» и имеет функцию, называемую «Photo Modules for PCM Remote Control Systems».

Детали детали

Номер произв TSOP1238SB1
Описание Photo Modules for PCM Remote Control Systems
Производители Vishay Telefunken
логотип Vishay Telefunken логотип 

8 Pages
scroll

No Preview Available !

TSOP1238SB1 Даташит, Описание, Даташиты
TSOP11..SB1
Vishay Telefunken
Photo Modules for PCM Remote Control Systems
Available types for different carrier frequencies
Type
TSOP1130SB1
TSOP1136SB1
TSOP1138SB1
TSOP1156SB1
fo
30 kHz
36 kHz
38 kHz
56 kHz
Type
TSOP1133SB1
TSOP1137SB1
TSOP1140SB1
fo
33 kHz
36.7 kHz
40 kHz
Description
The TSOP11..SB1 – series are miniaturized receivers
for infrared remote control systems. PIN diode and
preamplifier are assembled on lead frame, the epoxy
package is designed as IR filter.
The demodulated output signal can directly be de-
coded by a microprocessor. The main benefit is the
operation with short burst transmission codes (e.g.
RECS 80) and high data rates.
96 12581
Features
D Photo detector and preamplifier in one package
D Internal filter for PCM frequency
D Improved shielding against electrical field distur-
bance
D TTL and CMOS compatibility
D Output active low
D Low power consumption
D High immunity against ambient light
Special Features
D Enhanced data rate of 3500 bit/s
D Operation with short bursts possible
(6 cycles/burst)
Block Diagram
Input
PIN
AGC
Control
Circuit
Band
Pass
80 kW
Demodu-
lator
2
VS
3
OUT
1
GND
94 8136
Document Number 82010
Rev. 8, 29-Mar-01
www.vishay.com
1 (8)









No Preview Available !

TSOP1238SB1 Даташит, Описание, Даташиты
TSOP11..SB1
Vishay Telefunken
Absolute Maximum Ratings
Tamb = 25_C
Parameter
Supply Voltage
Supply Current
Output Voltage
Output Current
Junction Temperature
Storage Temperature Range
Operating Temperature Range
Power Consumption
Soldering Temperature
Test Conditions
(Pin 2)
(Pin 2)
(Pin 3)
(Pin 3)
x(Tamb 85 °C)
xt 10 s, 1 mm from case
Symbol
VS
IS
VO
IO
Tj
Tstg
Tamb
Ptot
Tsd
Value
–0.3...6.0
5
–0.3...6.0
5
100
–25...+85
–25...+85
50
260
Unit
V
mA
V
mA
°C
°C
°C
mW
°C
Basic Characteristics
Tamb = 25_C
Parameter
Supply Current (Pin 2)
Supply Voltage (Pin 2)
Transmission Distance
Output Voltage Low (Pin 3)
Irradiance (30 – 40 kHz)
Irradiance (56 kHz)
Irradiance
Directivity
Test Conditions
VS = 5 V, Ev = 0
VS = 5 V, Ev = 40 klx, sunlight
Ev = 0, test signal see fig.8,
IR diode TSAL6200, IF = 0.4 A
IOSL = 0.5 mA,Ee = 0.7 mW/m2,
f = fo, test signal see fig.7
Test signal see fig.7
Test signal see fig.8
Test signal see fig.7
Test signal see fig.8
Test signal see fig.7
Angle of half transmission distance
Symbol
ISD
ISH
VS
d
VOSL
Ee min
Ee min
Ee min
Ee min
Ee max
ϕ1/2
Min
0.4
4.5
30
Typ
0.6
1
35
0.4
0.35
0.45
0.40
±45
Max Unit
1.5 mA
mA
5.5 V
m
250 mV
0.6 mW/m2
0.5 mW/m2
0.7 mW/m2
0.6 mW/m2
W/m2
deg
Application Circuit
100 W *)
TSAL62..
mTSOP11.. 2 4.7 F *)
3
>10 kW
optional
**)
mC
+5V
12755
1
GND
*) recommended to suppress power supply disturbances
**) The output voltage should not be hold continuously at a voltage below 3.3V by the external circuit.
www.vishay.com
2 (8)
Document Number 82010
Rev. 8, 29-Mar-01









No Preview Available !

TSOP1238SB1 Даташит, Описание, Даташиты
TSOP11..SB1
Vishay Telefunken
Suitable Data Format
The circuit of the TSOP11..SB1 is designed in that
way that unexpected output pulses due to noise or
disturbance signals are avoided. A bandpassfilter, an
integrator stage and an automatic gain control are
used to suppress such disturbances.
The distinguishing mark between data signal and
disturbance signal are carrier frequency, burst length
and duty cycle.
The data signal should fullfill the following condition:
Carrier frequency should be close to center
frequency of the bandpass (e.g. 38kHz).
Burst length should be 6 cycles/burst or longer.
After each burst which is between 6 cycles and 70
cycles a gap time of at least 10 cycles is neccessary.
For each burst which is longer than 1.8ms a
corresponding gap time is necessary at some time in
the data stream. This gap time should have at least
same length as the burst.
Up to 2200 short bursts per second can be received
continuously.
Some examples for suitable data format are:
NEC Code, Toshiba Micom Format, Sharp Code, RC5
Code, RC6 Code, RCMM Code, R–2000 Code,
RECS–80 Code.
When a disturbance signal is applied to the
TSOP11..SB1 it can still receive the data signal.
However the sensitivity is reduced to that level that no
unexpected pulses will occure.
Some examples for such disturbance signals which
are suppressed by the TSOP11..SB1 are:
DC light (e.g. from tungsten bulb or sunlight)
Continuous signal at 38kHz or at any other
frequency
Signals from fluorescent lamps with electronic
ballast (an example of the signal modulation is in the
figure below).
0 5 10 15 20
time [ms]
IR Signal from Fluorescent Lamp with low Modulation
Document Number 82010
Rev. 8, 29-Mar-01
www.vishay.com
3 (8)










Скачать PDF:

[ TSOP1238SB1.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
TSOP1238SB1Photo Modules for PCM Remote Control SystemsVishay Telefunken
Vishay Telefunken

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск