DataSheet26.com

73K222AL-IH PDF даташит

Спецификация 73K222AL-IH изготовлена ​​​​«ETC» и имеет функцию, называемую «V.22/ V.21/ Bell 212A/ 103 Single-Chip Modem».

Детали детали

Номер произв 73K222AL-IH
Описание V.22/ V.21/ Bell 212A/ 103 Single-Chip Modem
Производители ETC
логотип ETC логотип 

28 Pages
scroll

No Preview Available !

73K222AL-IH Даташит, Описание, Даташиты
73K222AL
V.22, V.21, Bell 212A, 103
Single-Chip Modem
DESCRIPTION
The 73K222AL is a highly integrated single-chip
modem IC which provides the functions needed to
construct a CCITT V.22, V.21 and Bell 212A
compatible modem, capable of 1200 bit/s full-duplex
operation over dial-up lines. The 73K222AL is an
enhancement of the 73K212L/AL single-chip modem
which adds V.22 and V.21 modes to the Bell 212A and
103 operation of the 73K212AL. In Bell 212A mode,
the 73K222AL provides the normal Bell 212A and 103
functions and employs a 2225 Hz answer tone. The
73K222AL in V.22 mode produces either 550 or 1800
Hz guard tone, recognizes and generates a 2100 Hz
answer tone, and allows 600 bit/s V.22 or 0-300 bit/s
V.21 operation. The 73K222AL integrates analog,
digital, and switched-capacitor array functions on a
single substrate, offering excellent performance and a
high level of functional integration in a single 28-pin
DIP, PLCC and 44-pin TQFP configuration. The
73K222AL operates from a single +5V supply. The
73K222AL is a new version replacing the 73K222L.
The 73K222AL should be specified for all new
designs.
The 73K222AL includes the DPSK and FSK
modulator/demodulator functions, call progress and
handshake tone monitor and a tone generator capable
of tone required for European applications.
(continued)
FEATURES
April 2000
One-chip CCITT V.22, V.21, Bell 212A and Bell
103 standard compatible modem data pump
Full-duplex operation at 0-300 bit/s (FSK) or 600
and 1200 bit/s (DPSK)
Pin and software compatible with other TDK
Semiconductor Corporation K-Series 1-chip
modems
Interfaces
directly
with
standard
microprocessors (8048, 80C51 typical)
Serial or parallel microprocessor bus for control
Serial port for data transfer
Both synchronous and asynchronous modes of
operation including V.22 extended overspeed
Call progress, carrier, precise answer tone
(2100 or 2225 Hz), and long loop detectors
DTMF, and 550 or 1800 Hz guard tone
generators
Test modes available: ALB, DL, RDL, Mark,
Space, Alternating bit patterns
Precise automatic gain control allows 45 dB
dynamic range
CMOS technology for low power consumption
using 60 mW @ 5V
Single +5 volt supply
PLCC and PDIP packages
AD0-AD7
RD
WR
ALE
CS
RESET
INT
TXD
RXD
DATA
BUS
BUFFER
READ
WRITE
CONTROL
LOGIC
STATUS
AND
CONTROL
LOGIC
BLOCK DIAGRAM
8-BIT
BUS
FOR
CONTROL
AND
STATUS
SERIAL
PORT
FOR
DATA
DIGITAL
PROCESSING
TESTS:
ALB, DLB
RDLB
PATTERNS
CLOCK
GENERATOR
FSK
MODULATOR/
DEMODULATOR
PSK
MODULATOR/
DEMODULATOR
SMART
DIALING
&
DETECT
FUNCTIONS
POWER
DTMF &
TONE
GENERATORS
TRANSMIT
FILTER
RECEIVE
FILTER
TXA
RXA









No Preview Available !

73K222AL-IH Даташит, Описание, Даташиты
73K222AL
V.22, V.21, Bell 212A, 103
Single-Chip
DESCRIPTION (continued)
This device supports V.22 (except mode v) and V. 21
modes of operation, allowing both synchronous and
asynchronous communications. Test features such as
analog loop, digital loop, and remote digital loopback are
supported. Internal pattern generators are also included for
self-testing. The 73K222AL is designed to appear to the
systems designer as a microprocessor peripheral, and will
easily interface with popular one-chip microprocessors
(80C51 typical) for control of modem functions through its 8-
bit multiplexed address/data bus or serial control bus. An
ALE control line simplifies address demultiplexing. Data
communications occurs through a separate serial port only.
The 73K222AL is ideal for use in either free standing or
integral system modem products where full-duplex 1200
bit/s data communications over the 2-wire switched
telephone network is desired. Its high functionality, low
power consumption and efficient packaging simplify
design requirements and increase system reliability. A
complete modem requires only the addition of the phone
line interface, a control microprocessor, and RS-232 level
converter for a typical system. The 73K222AL is part of
TDK Semiconductor Corporation's K-Series family of pin
and function compatible single-chip modem products.
These devices allow systems to be configured for higher
speeds and Bell or CCITT operation with only a single
component change.
OPERATION
ASYNCHRONOUS MODE
Data transmission for the DPSK mode requires that data
ultimately be transmitted in a synchronous fashion. The
73K222AL includes ASYNC/SYNC and SYNC/ASYNC
converters which delete or insert stop bits in order to
transmit data within a ±0.01% rate. In asynchronous mode
the serial data comes from the TXD pin into the
ASYNC/SYNC converter. The ASYNC/SYNC converter
accepts the data provided on the TXD pin which normally
must be 1200 or 600 bit/s +1.0%, -2.5%. The converter will
then insert or delete stop bits in order to output a signal
which is 1200 or 600 bit/s ± 0.01% (± 0.01% is required
synchronous data rate accuracy).
The serial data stream from the ASYNC/SYNC
converter is passed through the data scrambler and
onto the analog modulator. The data scrambler can be
bypassed under processor control when unscrambled
data must be transmitted. The ASYNC/SYNC
converter and the data scrambler are bypassed in all
FSK modes. If serial input data contains a break signal
through one character (including start and stop bits)
the break will be extended to at least 2 times N + 3 bits
2
long (where N is the number of transmitted
bits/character).
Serial data from the demodulator is passed first
through the data descrambler and then through
the SYNC/ASYNC converter. The SYNC/ASYNC
convertor will reinsert any deleted stop bits and
transmit output data at an intra-character rate (bit-
to-bit timing) of no greater than 1219 bit/s. An
incoming break signal (low through two
characters) will be passed through without
incorrectly inserting a stop bit.
The SYNC/ASYNC converter also has an
extended overspeed mode which allows selection
of an overspeed range of either +1% or +2.3%. In
the extended overspeed mode, stop bits are
output at 7/8 the normal width.
SYNCHRONOUS MODE
The CCITT V.22 standard defines synchronous
operation at 600 and 1200 bit/s. The Bell 212A
standard defines synchronous operation only at
1200 bit/s. Operation is similar to that of the
asynchronous mode except that data must be
synchronized to a provided clock and no variation
in data transfer rate is allowable. Serial input data
appearing at TXD must be valid on the rising edge
of TXCLK.
TXCLK is an internally derived signal in internal mode
and is connected internally to the RXCLK pin in slave
mode. Receive data at the RXD pin is clocked out on
the falling edge of RXCLK. The ASYNCH/SYNCH
converter is bypassed when synchronous mode is
selected and data is transmitted out at the same rate
as it is input.
DPSK MODULATOR/DEMODULATOR
The 73K222AL modulates a serial bit stream into
di-bit pairs that are represented by four possible
phase shifts as prescribed by the Bell 212A or
V.22 standards. The baseband signal is then
filtered to reduce intersymbol interference on the
bandlimited 2-wire telephone line. Transmission
occurs using either a 1200 Hz (originate mode) or
2400 Hz carrier (answer mode). Demodulation is
the reverse of the modulation process, with the
incoming analog signal eventually decoded into di-
bits and converted back to a serial bit stream. The
demodulator also recovers the clock which was
encoded into the analog signal during modulation.
Demodulation occurs using either a 1200 Hz
carrier (answer mode or ALB originate mode) or a









No Preview Available !

73K222AL-IH Даташит, Описание, Даташиты
2400 Hz carrier (originate mode or ALB answer mode).
The 73K222AL uses a phase locked loop coherent
demodulation technique for optimum receiver
performance.
FSK MODULATOR/DEMODULATOR
The FSK modulator produces a frequency modulated
analog output signal using two discrete frequencies to
represent the binary data. In Bell 103, the standard
frequencies of 1270 and 1070 Hz (originate, mark and
space) or 2225 and 2025 Hz (answer, mark and space)
are used. V.21 mode uses 980 and 1180 Hz (originate,
mark and space), or 1650 and 1850Hz (answer, mark and
space). Demodulation involves detecting the received
frequencies and decoding them into the appropriate binary
value. The rate converter and scrambler/ descrambler are
bypassed in the 103 or V.21 modes.
PASSBAND FILTERS AND EQUALIZERS
High and low band filters are included to shape the
amplitude and phase response of the transmit and
receive signals and provide compromise delay
equalization and rejection of out-of-band signals in the
receive channel. Amplitude and phase equalization are
necessary to compensate for distortion of the
transmission line and to reduce intersymbol
interference in the bandlimited receive signal. The
transmit signal filtering approximates a 75% square
root of raised Cosine frequency response
characteristic.
AGC
The automatic gain control maintains a signal level at
the input to the demodulators which is constant to
within 1 dB. It corrects quickly for increases in signal
which would cause clipping and provides a total
receiver dynamic range of >45 dB.
PARALLEL BUS INTERFACE
Four 8-bit registers are provided for control, option
select and status monitoring. These registers are
addressed with the AD0, AD1, and AD2 multiplexed
address lines (latched by ALE) and appear to a control
microprocessor as four consecutive memory locations.
Two control registers and the tone register are
read/write memory. The detect register is read only
and cannot be modified except by modem response to
monitored parameters.
73K222AL
V.22, V.21, Bell 212A, 103
Single-Chip Modem
SERIAL COMMAND INTERFACE
The serial command interface allows access to the
73K222AL control and status registers via a serial
command port (22-pin version only). In this mode the
A0, A1 and A2 lines provide register addresses for
data passed through the data pin under control of the
RD and WR lines. A read operation is initiated when
the RD line is taken low. The first bit is available after
RD is brought low and the next seven cycles of
EXCLK will then transfer out seven bits of the
selected address LSB first. A write takes place by
shifting in eight bits of data LSB first for eight
consecutive cycles of EXCLK. WR is then pulsed low
and data transferred into the addressed register
occurs on the rising edge of WR. This interface
mode is also supported in the 28-pin packages. See
serial control interface pin description.
SPECIAL DETECT CIRCUITRY
The special detect circuitry monitors the received
analog signal to determine status or presence of
carrier, call-progress tones, answer tone and weak
received signal (long loop condition). An
unscrambled mark request signal is also detected
when the received data out of the DPSK
demodulator before the descrambler has been high
for 165.5 ms ± 6.5 ms minimum. The appropriate
detect register bit is set when one of these conditions
changes and an interrupt is generated for all
purposes except long loop. The interrupts are
disabled (masked) when the enable interrupt bit is
set to 0.
DTMF GENERATOR
The DTMF generator will output one of 16 standard
tone pairs determined by a 4-bit binary value and TX
DTMF mode bit previously loaded into the tone
register. Tone generation is initiated when the DTMF
mode is selected using the tone register and the
transmit enable (CR0 bit D1) is changed from 0 to 1.
3










Скачать PDF:

[ 73K222AL-IH.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
73K222AL-IGTV.22/ V.21/ Bell 212A/ 103 Single-Chip ModemETC
ETC
73K222AL-IHV.22/ V.21/ Bell 212A/ 103 Single-Chip ModemETC
ETC
73K222AL-IPV.22/ V.21/ Bell 212A/ 103 Single-Chip ModemETC
ETC

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск