DataSheet26.com

M-991 PDF даташит

Спецификация M-991 изготовлена ​​​​«Clare Inc.» и имеет функцию, называемую «Call Progress Tone Generator».

Детали детали

Номер произв M-991
Описание Call Progress Tone Generator
Производители Clare Inc.
логотип Clare  Inc. логотип 

6 Pages
scroll

No Preview Available !

M-991 Даташит, Описание, Даташиты
Features
Generates standard call progress tones
Digital input control
Linear (analog) output
Power output capable of driving standard line
14-pin DIP and 16-pin SOIC package types
Single supply 5V CMOS (low power)
Inexpensive 3.58 MHz time base
Temperature range from -25ºC to 70ºC (-01 ver-
sion)
Temperature range from -40ºC to 85ºC (-02 ver-
sion)
Applications
Telephone systems
Test equipment
Callback
Security systems
Billing systems
M-991
Call Progress Tone Generator
Description
The M-991 is a call progress tone generator integrated
circuit for use in telephone systems. The circuit uses
low-power CMOS techniques to generate tones which
are digitally controlled and highly linear. The M-991 is
designed to permit operation with almost any system.
The use of integrated circuit techniques allows the M-
991 to incorporate the control, tone generating, and
power output buffer into a single 14-pin DIP or a 16-pin
SOIC. A 3.58-MHz (color burst) crystal-controlled time
base guarantees accuracy and repeatability.
Ordering Information
Part #
M-991
M-991-01SM
M-991-01SMTR
M-991-02SM
M-991-02SMTR
Description
14-pin plastic DIP
16-pin SOIC
16-pin SOIC Tape and Reel
16-pin SOIC, Extended
Temperature Range
16-pin SOIC, Extended
Temperature Range, Tape and
Reel
Pin Assignments
Block Diagram
DS-M991-R1
www.clare.com
1









No Preview Available !

M-991 Даташит, Описание, Даташиты
M-991
Absolute Maximum Ratings
Storage Temperature
-55° to 125° C
Operating Ambient Temperature
-25° to 70° C
Operating Ambient Temperature
for the M-991-02SM
-40° to 85° C
VDD 7.0V
Any Input Voltage
VSS -0.6 to VDD +0.6V
Note:
1. Exceeding these ratings may permanently damage the M-991.
Absolute Maximum Ratings are stress ratings. Stresses in
excess of these ratings can cause permanent damage to
the device. Functional operation of the device at these or
any other conditions beyond those indicated in the opera-
tional sections of this data sheet is not implied. Exposure of
the device to the absolute maximum ratings for an extend-
ed period may degrade the device and effect its reliability.
Specifications
Parameter
Power Supply
and Reference
VDD
Current Drain, IDD
Oscillator
VREF Pin:
Deviation from (VDD + VSS)/2
Internal Resistance from VREF
to VDD, VSS
Frequency Deviation
External Clock: (XOUT open)
VIL
VIH
Duty Cycle
XIN, XOUT Loading:
Capacitance
Resistance
Tone Output
Frequency Deviation
Level
Distorting Components
Idle
OUTDRIVE Envelope Rise Time
Control
DX, CE Pns:
VIL
VIH
Mute Pins:
VOL (ISINK = -100 µA)
Timing
VOH (ISOURCE = 100 µA)
Data Setup (tDS)
Data Hold (tDH)
Chip Enable Fall (tPL)
Tone On Delay (tTO)
Tone Off Delay (tTD)
Mute Delay from Outdrive (tMO)
Notes: (unless otherwise specified)
1.
2.
All DC voltages are
Vrms per tone, 540
referenced
W load.
to
VSS.
3. Any one frequency relative to the lowest level output tone (f<4000 Hz).
4. 0 dBm = 0.775 Vrms.
5. To 90% maximum amplitude.
6. For all supply voltages in the operating range.
Min
4.75
-
-2
3.25
-0.01
0
VDD - 0.2
40
-
20
-0.5
100
-35
-
-
-
2.5
-
VDD - 1.5
200
10
-
-
-
-
Typ
-
2.0/4.0
Max
5.25
-
Units
V
mA
- +2 %
- 6.75 k
- +0.01 %
- 0.2 V
- VDD V
- 60 %
- 10 pF
- - M
- +0.5 %
- 180 mV
- - dB
- -60 dBm
- 4 ms
- 0.5 V
--V
- 1.5
--
--
--
- 90
-5
-5
- 200
7. At XOUT pin as compared to 3.579545 MHz.
8. OUTDRIVE with load >5 KW/OUTDRIVE with
540 W load.
9. Resistance at VREF to VDD or VSS > 1 MW.
10. Crystal oscillator active.
11. Measured 90% to 10%.
V
V
ns
ns
ns
ms
ms
ns
Notes
1
8
7
10
-
-
2
3
4
5
6
11
2
www.clare.com
Rev. 1









No Preview Available !

M-991 Даташит, Описание, Даташиты
M-991
Call Progress Tone Generation
Call progress tones are audible tones sent from
switching systems to calling parties (or equipment) to
indicate the status of calls. Calling parties can identify
the success of a placed call by what is heard after dial-
ing. The M-991 series utilizes a highly linear tone gen-
erator that produces the unique frequencies (singly or
in pairs) that are common to call progress signals.
Duration and frequency selection are digitally con-
trolled (see the Data/Tone Selection table below for
data settings for a particular tone output). A typical
control sequence for the M-991 is: (1) set data lines to
desired frequency selection, (2) wait for data lines to
settle, (3) drive the chip enable (CE) low, (4) maintain
CE low for desired tone duration (Note: data lines may
be changed after data hold time), and (4) return CE to
a logic high. (Commonly used call progress tones are
shown in the Data/Tone Selection table below.) In a
bus-oriented system, noise on the data lines may
propagate through the device and appear at the out-
put. To safeguard against this, use an external latch to
lock the data into the device. In addition, it is good
practice to bypass the VREF pin to ground with a small
capacitor (0.01 mF) to reduce power supply noise. The
designer should be aware of device timing require-
ments and design accordingly. The data input pins
may be tied high (+5 VDC) or low (ground) as required,
but D4 and D5 must be left open. Beware of hardwiring
the CE pin for dedicated tone generation. This input is
edge triggered. An RC network like that shown in the
Power-on Reset Circuit on Page 4 should be used to
momentarily reset the device immediately following
power-up to ensure proper operation.
Data/Tone Selection
D0 D1 D2 D3 Frequency (Hz)
Use
12
0 0 0 0 350
440 Dial Tone
0 0 0 1 400
off Special
0 0 1 0 440
off Alert Tone
0 0 1 1 440
480 Audible Ring
0 1 0 0 440
620 Pre-empt
0 1 0 1 480
off Bell high tone
0 1 1 0 480
620 Reorder(Bell low)
0 1 1 1 350
off Special
1 0 0 0 620
off Special
1 0 0 1 941
1209 DTMF “*
Standard Call Progress Tones
Pin Function
Pin
CE
D0 - D3
D4-D5
MUTE
OUTDRIVE
VDD
VREF
VSS
XIN
XOUT
Function
Latches data and enables output (active
low input).
Data input pins. (See Data/Tone Selection.)
Leave open.
Output indicates that a signal is being generated at
OUTDRIVE.
Linear buffered tone output.
Most positive power supply input pin.
Internally generated mid-power supply voltage
(output).
Most negative power supply input pin.
Crystal oscillator or digital clock input.
Crystal oscillator output.
Tone Name
Dial
Reorder
Busy
Audible Ring
Recall Dial
Special AR
Intercept
Call Waiting
Busy Verification
Executive Override
Confirmation
Frequency (Hz)
12
350 440
480 620
480 620
440 480
350 440
440 480
440 620
440 Off
440 Off
440 Off
350 440
Interruption Rate
Steady
Repeat, tones on and off 250 ms ± 25 ms each.
Repeat, tones on and off 500 ms ± 50 ms each.
Reat, tones on 2 ± 0.2 s, tones off 4 ± 0.4 s
Three bursts tones on and off 100 ms ± 20 ms each followed by dial tone.
Tones on 1 ± 0.2s, followed by single 440 Hz on for 0.2s on, and silence for 3 ±
0.3 s, repeat.
Repeat alternating tones, each on for 230 ms ± 70 ms with total cycle of 500 ±
50 ms.
One burst 200 ± 100 ms
One burst of tone on 1.75 ± 0.25 s before attendant intrudes, followed by burst
of tone 0.65 ± 0.15 s on, 8 to 20 s apart for as long as the call lasts
One burst of tone for 3 ± 1 s before overriding station intrudes
Three bursts on and off 100 ms each or 100 ms on, 100 ms off, 300 ms on
Rev. 1 www.clare.com
3










Скачать PDF:

[ M-991.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
M-991Call Progress Tone GeneratorClare  Inc.
Clare Inc.
M-991-01SMCall Progress Tone GeneratorClare  Inc.
Clare Inc.
M-991-01SMTRCall Progress Tone GeneratorClare  Inc.
Clare Inc.
M-991-02SMCall Progress Tone GeneratorClare  Inc.
Clare Inc.

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск