DataSheet26.com

SA1C-FK PDF даташит

Спецификация SA1C-FK изготовлена ​​​​«IDEC» и имеет функцию, называемую «Fiber Optic Analog Sensors».

Детали детали

Номер произв SA1C-FK
Описание Fiber Optic Analog Sensors
Производители IDEC
логотип IDEC логотип 

25 Pages
scroll

No Preview Available !

SA1C-FK Даташит, Описание, Даташиты
Fiber Optic: SA1C-FK
Fiber Optic Analog: SA1C-FK
Sensors
• High-speed, miniature photoelectric sensors with
analog (4 - 20mA) and digital output
• Senses gradual color changes
• Available in both red and green LEDs
• Through-beam and reflected-light sensing available
• Ideal for either color mark applications or simple
presence and absence applications requiring analog
output
• Compact size allows for DIN rail mounting
• Fiber optic units available to address specific applica-
tion needs
• Simple to install
• IP66 protection rating
Built on the foundation of SA1C-F, SA1C-FK is ideal for either color mark applications or simple presence
and absence applications requiring analog output.
Featuring analog and digital output, this sensor comes in through-beam or reflected-light sensing styles.
164 www.idec.com









No Preview Available !

SA1C-FK Даташит, Описание, Даташиты
Sensors
Dimensions (mm)
Fiber Optic: SA1C-FK
Panel Mounting Bracket (attachment)
Not required for DIN Rail mounting
Mounting Hole Layout
Receiver
Emitter
holes
(when using a panel
mounting bracket)
Specifications
SA1C-FK3
Light Source Element
Red LED
Green LED
Sensing Distance
Depends on the fiber unit (see page 173)
Power Voltage
12 to 24V DC (Operating voltage: 10 to 30V DC) ripple 10% maximum
Current Draw
80mA maximum
Analog Current Output
4 to 20mA, 5V DC maximum 1
Digital Output
NPN open collector 30V DC, 100mA maximum,1.5V maximum with short circuit protection
Operation Mode
Dark ON (connect MODE line to GND line)
Light ON (connect MODE line to power line)
Response
0.5ms maximum 2
Indicator
Operation LED: Red, Stable LED: Green
Detectable Object
Translucent object, opaque object
Hysteresis
20% maximum (using reflex fiber unit)
Sensitivity
4-turn adjustment
Operation Point Control
1 turn
Receiver Element
Photo diode
Operating Temperature
–25 to +55˚C (performance will be adversely affected if the sensor becomes coated with ice)
Storage Temperature
–30 to +70˚C (performance will be adversely affected if the sensor becomes coated with ice)
Operating Humidity
35 to 85% RH (avoid condensation)
Extraneous Light Immunity Sunlight: 10,000 lux maximum; Incandescent light: 3,000 lux (at the receiver)
Noise Resistance
Normal mode: 500V (50ns to 1μs, 100Hz: Using a noise simulator)
Common mode: 300V (50ns to 1μs, 100Hz: Using a noise simulator)
Insulation Resistance
Between live and dead parts: 20MΩ minimum, with 500V DC megger
Dielectric Strength
Between live and dead parts: 1,000V, 1 minute
Vibration Resistance
Damage limits: 10 to 55Hz; Single amplitude: 0.75mm 20 cycles in each of 3 axes
Shock Resistance
Damage limits: 500 m/sec2 10 cycles in each of 3 axes
Degree of Protection
IP66—IEC Pub 529
Cable
Cable type: Ø4.4mm 5-core vinyl cabtyre cable 0.2mm2, 6’–6-3/4” (2m) long
Material
Housing: PBT
Accessories
Mounting bracket, adjusting screwdriver, load resistor (249Ω) for converting analog amperage
to voltage (1 to 5V)
Interference Prevention
Up to 2 units can be installed in close proximity. For analog output, interference prevention is
not possible.
Weight
Approximately 75g
1. Analog current output specification is based on the power voltage range from 12 to 24V DC (±10%).
Use the attached resistor (249Ω, 1/4W) as a load resistance for converting analog output to voltage.
2. Response time for analog current output is between 10% and 90% of the rise or fall of the voltage signal when using a 249Ω resistor.
SA1C-FK3G
USA: 800-262-IDEC Canada: 888-317-IDEC
165









No Preview Available !

SA1C-FK Даташит, Описание, Даташиты
Fiber Optic: SA1C-FK
Part Numbers
Function
Light Source Element Output
Red LED
Green LED
Analog output + NPN output
Function is determined by the fiber optic unit used.
Applications
Sensors
Part Number
SA1C-FK3
SA1C-FK3G
For information on accessories, see
page 171.
166 www.idec.com










Скачать PDF:

[ SA1C-FK.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
SA1C-FKFiber Optic Analog SensorsIDEC
IDEC

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск