|
|
Número de pieza | DMC-50747NF | |
Descripción | LCD Module | |
Fabricantes | OPTREX CORPORATION | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de DMC-50747NF (archivo pdf) en la parte inferior de esta página. Total 17 Páginas | ||
No Preview Available ! LCD Module Specification
Type No. DMC-50747NF
First Edition
Apr 22, 1999
Final Revision
*******
Approved by
Checked by
Checked by
Prepared by
Production Div.
Quality Assurance Div.
Design Engineering Div.
Production Div.
Table of Contents
1. General Specifications.................................................................2
2. Electrical Specifications...............................................................3
3. Optical Specifications..................................................................7
4. I/O Terminal..............................................................................9
5. Test........................................................................................11
6. Appearance Standards................................................................12
7. Code System of Production Lot................................................15
8. Applying Precautions................................................................15
9. Precautions Relating Product Handling.......................................16
10. Warranty..................................................................................17
Rev. Date
Revision History
Page
Comment
DMC-50747NF (AA) No.99-0095
OPTREX OPTREX CORPORATION
Page 1/17
1 page 2.3.2.System Bus Write Characteristics 2 (68 series MPU)
VDD=3.0V±10%
Parameter
Symbol
Min. Max. Units
System Cycle Time
tCYC
500
Address Setup Time
tAW 60
Address Hold Time
tAH 30
Data Setup Time
tDS 100
Data Hold Time
tDH 50
Enable Pulse Width
tEW 100
Note 1 : For the rise and fall of an input signal, set a value not exceeding 25ns.
Note 2 : Every timing is specified on the basis of 20% and 80% of VDD.
–
–
–
–
–
–
ns
ns
ns
ns
ns
ns
tCYC
E
A0, CS
tAW tEW tAH
tDS tDH
D0~D7
DMC-50747NF (AA) No.99-0095
OPTREX OPTREX CORPORATION
Page 5/17
5 Page 5.Test
No change on display and in operation under the following test condition.
No. Parameter
Conditions
Notes
1 High Temperature Operating 50˚C±2˚C, 96hrs (operation state)
3
2 Low Temperature Operating
0˚C±2˚C, 96hrs (operation state)
4
3 High Temperature Storage
70˚C±2˚C, 96hrs
5
4 Low Temperature Storage
-20˚C±2˚C, 96hrs
4, 5
5 Damp Proof Test
40˚C±2˚C, 90~95%RH, 96hrs
4, 5
6 Heat Shock Test
-25˚C (30min) → 25˚C (5min) → 70˚C (30min)
→ 25˚C (5min) 5 cycles
4
7 Vibration Test
Total fixed amplitude : 1.5mm
6
Vibration Frequency : 10~55Hz
One cycle 60 seconds to 3 directions of X, Y, Z for
each 15 minutes
Note 1 : Unless otherwise specified, tests will be conducted under the following condition.
Temperature : 20±5˚C
Humidity : 65±5%
Note 2 : Unless otherwise specified, tests will be not conducted under functioning state.
Note 3 : It should be checked at the actual driving condition under the high temperature.
Note 4 : No dew condensation to be observed.
Note 5 : The function test shall be conducted after 4 hours storage at the normal temperature and humidity
after removed from the test chamber.
Note 6 : Vibration test will be conducted to the product itself without putting it in a container.
DMC-50747NF (AA) No.99-0095
OPTREX OPTREX CORPORATION
Page 11/17
11 Page |
Páginas | Total 17 Páginas | |
PDF Descargar | [ Datasheet DMC-50747NF.PDF ] |
Número de pieza | Descripción | Fabricantes |
DMC-50747NF | LCD Module | OPTREX CORPORATION |
DMC-50747NF-AK | LCD Module Technical Specification | OPTREX CORPORATION |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |