DataSheet26.com

AD5172 PDF даташит

Спецификация AD5172 изготовлена ​​​​«Analog Devices» и имеет функцию, называемую «Dual-Channel I2C Digital Potentiometers».

Детали детали

Номер произв AD5172
Описание Dual-Channel I2C Digital Potentiometers
Производители Analog Devices
логотип Analog Devices логотип 

28 Pages
scroll

No Preview Available !

AD5172 Даташит, Описание, Даташиты
Data Sheet
256-Position, One-Time Programmable,
Dual-Channel, I2C Digital Potentiometers
AD5172/AD5173
FEATURES
2-channel, 256-position potentiometers
One-time programmable (OTP) set-and-forget resistance
setting provides a low cost alternative to EEMEM
Unlimited adjustments prior to OTP activation
OTP overwrite allows dynamic adjustments with user-
defined preset
End-to-end resistance: 2.5 kΩ, 10 kΩ, 50 kΩ, and 100 kΩ
Compact 10-lead MSOP: 3 mm × 4.9 mm
Fast settling time: tS = 5 μs typical on power-up
Full read/write of wiper register
Power-on preset to midscale
Extra package address decode pins: AD0 and AD1 (AD5173 )
Single supply: 2.7 V to 5.5 V
Low temperature coefficient: 35 ppm/°C
Low power: IDD = 6 μA maximum
Wide operating temperature: −40°C to +125°C
FUNCTIONAL BLOCK DIAGRAMS
A1 W1 B1
A2 W2 B2
VDD
GND
FUSE
LINKS
12
RDAC
REGISTER 1
RDAC
REGISTER 2
SDA
SCL
/8
SERIAL INPUT
REGISTER
Figure 1. AD5172 Functional Block Diagram
W1 B1
W2 B2
APPLICATIONS
Systems calibration
Electronics level setting
Mechanical trimmers replacement in new designs
Permanent factory PCB setting
Transducer adjustment of pressure, temperature, position,
chemical, and optical sensors
RF amplifier biasing
Automotive electronics adjustment
Gain control and offset adjustment
GENERAL DESCRIPTION
The AD5172/AD5173 are dual-channel, 256-position, one-time
programmable (OTP) digital potentiometers1 that employ fuse
link technology to achieve memory retention of resistance
settings. OTP is a cost-effective alternative to EEMEM for users
who do not need to program the digital potentiometer setting
in memory more than once. These devices perform the same
electronic adjustment function as mechanical potentiometers or
variable resistors but with enhanced resolution, solid-state reliabil-
ity, and superior low temperature coefficient performance.
The AD5172/AD5173 are programmed using a 2-wire, I2C®-
compatible digital interface. Unlimited adjustments are allowed
VDD
GND
FUSE
LINKS
12
RDAC
REGISTER 1
RDAC
REGISTER 2
AD0 ADDRESS
/AD1
DECODE
8
SDA
SCL
SERIAL INPUT
REGISTER
Figure 2. AD5173 Functional Block Diagram
before permanently setting the resistance value. During OTP
activation, a permanent blow fuse command freezes the wiper
position (analogous to placing epoxy on a mechanical trimmer).
Unlike traditional OTP digital potentiometers, the AD5172/
AD5173 have a unique temporary OTP overwrite feature that
allows for new adjustments even after a fuse is blown. However,
the OTP setting is restored during subsequent power-up condi-
tions. This allows users to treat these digital potentiometers as
volatile potentiometers with a programmable preset.
1 The terms digital potentiometer, VR, and RDAC are used interchangeably.
Rev. I
Document Feedback
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarksandregisteredtrademarksarethepropertyoftheirrespectiveowners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700 ©2003–2013 Analog Devices, Inc. All rights reserved.
Technical Support
www.analog.com









No Preview Available !

AD5172 Даташит, Описание, Даташиты
AD5172/AD5173
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications....................................................................................... 1
Functional Block Diagrams............................................................. 1
General Description ......................................................................... 1
Revision History ............................................................................... 3
Specifications..................................................................................... 4
Electrical Characteristics: 2.5 kΩ ............................................... 4
Electrical Characteristics: 10 kΩ, 50 kΩ, and 100 kΩ ............. 5
Timing Characteristics ................................................................ 7
Absolute Maximum Ratings............................................................ 8
ESD Caution.................................................................................. 8
Pin Configurations and Function Descriptions ........................... 9
Typical Performance Characteristics ........................................... 10
Test Circuits..................................................................................... 15
Theory of Operation ...................................................................... 16
One-Time Programming (OTP) .............................................. 16
Data Sheet
Programming the Variable Resistor and Voltage ................... 16
Programming the Potentiometer Divider............................... 17
ESD Protection ........................................................................... 18
Terminal Voltage Operating Range ......................................... 18
Power-Up Sequence ................................................................... 18
Power Supply Considerations ................................................... 18
Layout Considerations............................................................... 19
I2C Interface .................................................................................... 20
Write Mode ................................................................................. 20
Read Mode .................................................................................. 20
I2C Controller Programming.................................................... 21
I2C-Compatible, 2-Wire Serial Bus.......................................... 22
Level Shifting for Different Voltage Operation ...................... 23
Outline Dimensions ....................................................................... 24
Ordering Guide .......................................................................... 25
Rev. I | Page 2 of 28









No Preview Available !

AD5172 Даташит, Описание, Даташиты
Data Sheet
REVISION HISTORY
8/13—Rev. H to Rev. I
Changed VA, VB, VW to GND and Digital Inputs and Output
Voltage to GND Rating to −0.3 V to +7 V or VDD + 0.3 V
(whichever is less); Table 4...............................................................7
Changes to Ordering Guide...........................................................25
4/09—Rev. G to Rev. H
Changes to DC Characteristics—Rheostat Mode Parameter and
to DC Characteristics—Potentiometer Divider Mode Parameter,
Table 1 .................................................................................................3
12/08—Rev. F to Rev. G
Changes to OTP Supply Voltage Parameter, Table 1 ....................3
Changes to OTP Supply Voltage Parameter, Table 2 ....................5
Changes to Table 5 and Table 6 .......................................................8
Changes to One-Time Programming (OTP) Section ................15
Changes to Power Supply Considerations Section, Figure 46,
and Figure 46 Caption ....................................................................17
Changes to Ordering Guide...........................................................23
7/08—Rev. E to Rev. F
Changes to Power Supplies Parameter in Table 1 and Table 2 ....3
Updated Fuse Blow Condition to 400 ms Throughout................5
1/08—Rev. D to Rev. E
Changes to Features ..........................................................................1
Changes to General Description .....................................................1
Changes to OTP Supply Voltage and OTP Supply Current in
Table 1 .................................................................................................3
Changes to OTP Supply Voltage and OTP Supply Current in
Table 2 .................................................................................................5
Added OTP Program Time in Table 3............................................6
Changes to Table 4 ............................................................................7
Changes to Table 5 and Table 6 .......................................................8
Inserted Figure 30............................................................................13
Replaced One-Time Programming (OTP) Section....................15
Replaced Power Supply Considerations Section.........................17
Deleted Device Programming Software Section.........................20
Replaced I2C-Compatible, 2-Wire Serial Bus Section................21
Changes to Ordering Guide...........................................................23
AD5172/AD5173
6/06—Rev. C to Rev. D
Changes to Features ..........................................................................1
Changes to One-Time Programming (OTP) Section ................15
Changes to Figure 44 and Figure 45 .............................................17
Changes to Power Supply Considerations Section .....................18
Changes to Figure 46 and Figure 47 .............................................18
Changes to Device Programming Software Section...................19
Updated Outline Dimensions........................................................24
6/05—Rev. B to Rev. C
Added Footnote 8, Footnote 9, and Footnote 10 to Table 1........3
Added Footnote 8 to Table 2............................................................5
Changes to Table 5 and Table 6 .......................................................9
Changes to Power Supply Considerations Section .....................17
Changes to I2C-Compatible 2-Wire Serial Bus Section .............23
Added Level Shifting for Different Voltage Operation Section.......24
Updated Outline Dimensions........................................................25
Changes to Ordering Guide...........................................................25
10/04—Rev. A to Rev. B
Updated Format ................................................................ Universal
Changes to Specifications.................................................................3
Changes to One-Time Programming (OTP) Section ................13
Changes to Power Supply Considerations Section .....................15
Changes to Figure 44 and Figure 45 .............................................15
Changes to Figure 46 and Figure 47 .............................................16
11/03—Rev. 0 to Rev. A
Changes to Electrical Characteristics—2.5 kΩ .............................3
11/03—Revision 0: Initial Version
Rev. I | Page 3 of 28










Скачать PDF:

[ AD5172.PDF Даташит ]

Номер в каталогеОписаниеПроизводители
AD5170I2C Digital PotentiometerAnalog Devices
Analog Devices
AD517164-Position OTP Digital PotentiometerAnalog Devices
Analog Devices
AD5172Dual-Channel I2C Digital PotentiometersAnalog Devices
Analog Devices
AD5173Dual-Channel I2C Digital PotentiometersAnalog Devices
Analog Devices

Номер в каталоге Описание Производители
TL431

100 мА, регулируемый прецизионный шунтирующий регулятор

Unisonic Technologies
Unisonic Technologies
IRF840

8 А, 500 В, N-канальный МОП-транзистор

Vishay
Vishay
LM317

Линейный стабилизатор напряжения, 1,5 А

STMicroelectronics
STMicroelectronics

DataSheet26.com    |    2020    |

  Контакты    |    Поиск