|
|
PDF BP3595 Data sheet ( Hoja de datos )
| Número de pieza | BP3595 | |
| Descripción | Built-in antenna IEEE802.11b/g/n (1x1) Wireless LAN Module | |
| Fabricantes | ROHM Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de BP3595 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
Built-in antenna IEEE802.11b/g/n (1x1) Wireless LAN Module BP3595
HARDWARE SPECIFICATION
Version 1.0.0
PROPRIETARY AND CONFIDENTIAL
1 page  
Built-in antenna IEEE802.11b/g/n (1x1) BP3591
Hardware specification
3 ABSOLUTE MAXIMUM RATINGS
2015/11/17
No. PARAMETER SYMBOL
1 Power supply voltage
VCC
2 Operating temperature range Topr
3 Storage temperature range
Tstg
LIMITS
-0.3 ～ +3.6
-40 ～ 85
-40 ～ 85
UNIT
V
℃
℃
REMARKS
DC
-
-
Note) Absolute maximum ratings are the values that must not be exceeded at any time under any
application or any test conditions. Please make design keeping enough margins accordingly.
PROPRIETARY AND CONFIDENTIAL 5/31
5 Page 
Built-in antenna IEEE802.11b/g/n (1x1) BP3591
Hardware specification
2015/11/17
TERMINAL
No. I/O
NAME
16 GND
-
17 USB_DM AI/O
18 USB_DP AI/O
19 GND
-
20 SDDATA2 I/O
21 SDDATA3 I/O
22 SDCMD I/O
23 VCC
-
24 VCC
-
25 SDCLK
I
26 SDDATA0 I/O
27 SDDATA1 I/O
28 HOST_SEL I(*)
29 FLASH_SEL I(*)
30 BOOT_SEL1 I(*)
Table 1. Module Terminal Functions (2/2)
FUNCTIONS
REMARKS
Ground
USB data minus
USB data plus
Ground
SDIO data 2
SDIO data 3
SDIO command
Power supply 3.3V
Power supply 3.3V
SDIO clock
SDIO data 0
SDIO data 1
Host I/F select
Flash memory area select
Boot mode select
-
-
-
-
-
-
-
Module power supply input
Module power supply input
-
-
-
0:USB, 1:SDIO
0:region1, 1:region2
(**)
(*) FLASH_SEL / HOST_SEL / BOOT_SEL0 / BOOT_SEL1 terminals hold the value after
reset (Power On Reset). After reset, these terminals are used for another purpose in the module.
There terminals have pull down resistance inside. Therefore, please set these terminals OPEN in
case of setting for “0” and Pull up 3.3V (power supply voltage) with 3kΩ～5kΩ resistor
(recommendation is 4.7kΩ resistor) in case of setting for “1”.
When the host MCU controls these terminal, please do not connect directly with output terminal
of host MCU and insert 3kΩ～5kΩ resistor (recommendation is 4.7kΩ resistor) between them.
When FLASH BOOT function is not used, FLASH_TXD terminal (pin 11) should be connected
pull down resistor of 47kΩ.
When FLASH BOOT function is used, FLASH_TXD terminal (pin 11) and FLASH_RXD (pin 14)
terminal would be connected pull down resistor, if you need.
PRST is POWER ON RESET terminal. It is connected 4.7kΩ resistor + 2.2uF capacitor at 3.3V
inside the module.
In case that need to watch the power supply voltage, please connect such as OPEN DRAIN
RESET IC for this terminal.
PROPRIETARY AND CONFIDENTIAL 11/31
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet BP3595.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| BP3595 | Built-in antenna IEEE802.11b/g/n (1x1) Wireless LAN Module | ROHM Semiconductor |
| BP3596 | Low Power Sub-1GHz Radio Module | ROHM Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |